MachinistCharts

Threads and tapping

Screw size chart and thread pitch chart

Short answer

A screw size chart gives each thread's diameter and pitch. Number screws are 0.060 in + 0.013 in × the number, so #10 is 0.190 in. Metric coarse pitches: M3 0.5 mm, M4 0.7, M5 0.8, M6 1.0, M8 1.25, M10 1.5, M12 1.75 mm. Common UNC: 1/4-20, 5/16-18, 3/8-16, 1/2-13. Common UNF: 1/4-28, 5/16-24, 3/8-24, 1/2-20.

By the MachinistCharts editors · Updated · 8 min read · Checked against ASME B1.1

Row of steel screws and bolts of increasing size beside an open thread pitch gauge

Key takeaways

  • Number screw major diameter = 0.060 in + 0.013 in × screw number: #6 is 0.138 in, #8 is 0.164 in, #10 is 0.190 in.
  • A metric size with no pitch stated is ISO coarse: M8 means M8 × 1.25, M10 means M10 × 1.5.
  • Pitch in mm = 25.4 ÷ threads per inch, so 1/4-20 UNC has a 1.270 mm pitch.
  • Pitch diameter d2 = d − 0.6495 × P; it is the diameter that controls thread fit.
  • 1/4-20 UNC-2A reads: 1/4 in diameter, 20 TPI, Unified coarse, class 2A external.

Screw size chart: number sizes and diameters

Inch machine screws below 1/4 in are sized by number, from #0 to #12. The major diameter is 0.060 in + 0.013 in × the screw number, so a #10 screw is 0.060 + 0.013 × 10 = 0.190 in (4.83 mm) across the threads.

The number only gives the diameter. The second number in a callout such as #10-24 or #10-32 is the thread count in threads per inch (TPI). Most number sizes come in a coarse (UNC) and a fine (UNF) series defined in ASME B1.1. #0 has only a fine thread, 80 TPI.

Screw sizeMajor diameter (in)Major diameter (mm)UNC (coarse)UNF (fine)
#00.0601.52—#0-80
#10.0731.85#1-64#1-72
#20.0862.18#2-56#2-64
#30.0992.51#3-48#3-56
#40.1122.84#4-40#4-48
#50.1253.17#5-40#5-44
#60.1383.51#6-32#6-40
#80.1644.17#8-32#8-36
#100.1904.83#10-24#10-32
#120.2165.49#12-24#12-28

Each thread in the table links to its tap drill page. The three number sizes searched most often: #6-32 has a 0.138 in major diameter, #8-32 is 0.164 in and #10-32 is 0.190 in. #5 and #12 are less common in stock than the others.

A number screw close to 5 mm is #10 (4.83 mm). The two are not interchangeable: an M5 has a 0.8 mm pitch, a #10-24 has 1.058 mm and a #10-32 has 0.794 mm. The metric vs imperial thread guide lists the nearest size for every common bolt.

Metric thread pitch chart (ISO 261)

A metric thread is named by its major diameter in millimeters: M8 is 8 mm. If no pitch is given, the thread is ISO coarse, so M8 means M8 × 1.25. Fine threads always state the pitch, as in M8 × 1.

The table gives the coarse pitch for M1.6 to M48, the usual fine pitch (from the ISO 262 selection), and the basic pitch and minor diameters of the coarse thread, calculated from the ISO 68-1 basic profile. The tap drill is the site's coarse tap drill, about major diameter minus pitch.

SizeMajor dia (mm)Major dia (in)Coarse pitch (mm)Fine pitch (mm)Pitch dia (mm)Minor dia, ext. (mm)Tap drill (mm)
M1.61.60.06300.350.21.3731.1711.25
M220.07870.40.251.7401.5091.6
M2.52.50.09840.450.352.2081.9482.05
M330.11810.50.352.6752.3872.5
M3.53.50.13780.60.353.1102.7642.9
M440.15750.70.53.5453.1413.3
M550.19690.80.54.4804.0194.2
M660.236210.755.3504.7735
M880.31501.2517.1886.4666.8
M10100.39371.51.25, 19.0268.1608.5
M12120.47241.751.5, 1.2510.8639.85310.2
M14140.551221.512.70111.54612
M16160.629921.514.70113.54614
M18180.70872.52, 1.516.37614.93315.5
M20200.78742.52, 1.518.37616.93317.5
M22220.86612.52, 1.520.37618.93319.5
M24240.94493222.05120.31921
M27271.06303225.05123.31924
M30301.18113.5227.72725.70626.5
M33331.29923.5230.72728.70629.5
M36361.41734333.40231.09332
M39391.53544336.40234.09335
M42421.65354.5339.07736.47937.5
M48481.88985344.75241.86643

Rule of thumb for metric coarse sizes: the pitch is roughly 1/8 to 1/6 of the diameter (M8 × 1.25, M12 × 1.75, M24 × 3). Above M24 the pitch climbs in 0.5 mm steps. Fine pitches are 1 to 2 steps finer and are used on adjusting screws, thin walls and hydraulic fittings.

Links in the size column go to the tap drill page for each thread, for example M6 × 1, M8 × 1.25, M10 × 1.5 and M12 × 1.75. Fine-thread pages include M8 × 1, M10 × 1.25 and M12 × 1.5.

UNC, UNF and UNEF thread chart (1/4 to 1 in)

Fractional inch threads are named by major diameter in inches and threads per inch: 1/4-20 UNC is a 0.250 in diameter with 20 threads per inch. UNC is Unified National Coarse, UNF is Unified National Fine and UNEF is Unified National Extra Fine, all in ASME B1.1.

Size (in)Major dia (in)Major dia (mm)UNC TPIUNC pitch (mm)UNF TPIUNF pitch (mm)UNEF TPI (pitch mm)
1/40.25006.35201.270280.90732 (0.794)
5/160.31257.94181.411241.05832 (0.794)
3/80.37509.53161.587241.05832 (0.794)
7/160.437511.11141.814201.27028 (0.907)
1/20.500012.70131.954201.27028 (0.907)
9/160.562514.29122.117181.41124 (1.058)
5/80.625015.88112.309181.41124 (1.058)
3/40.750019.05102.540161.58720 (1.270)
7/80.875022.2392.822141.81420 (1.270)
11.000025.4083.175122.11720 (1.270)

Pitch in millimeters is 25.4 ÷ TPI. 1/4-20 has a 1.270 mm pitch, 1/2-13 has 1.954 mm. UNEF is used on thin-wall tube, instrument fittings and bicycle and aerospace parts where only a shallow thread fits. The UNC vs UNF guide compares strength and use.

Fractional tap drills and torque values are on the tap drill chart and the bolt torque chart, for example 1/4-20, 5/16-18, 3/8-16 and 1/2-13.

What is thread pitch?

Thread pitch is the distance from one thread crest to the next, measured parallel to the axis. Metric threads state pitch in millimeters; inch threads state threads per inch, which is the inverse: pitch = 1 ÷ TPI inches, or 25.4 ÷ TPI millimeters.

Pitch is not the same as lead. Lead is how far the screw advances in one turn. On a normal single-start thread lead equals pitch. On a two-start thread the lead is twice the pitch, which is why multi-start threads appear on bottle caps and fast-acting lead screws.

Threads per inchPitch (in)Pitch (mm)
800.01250.318
640.01560.397
560.01790.454
480.02080.529
400.02500.635
320.03120.794
280.03570.907
240.04171.058
200.05001.270
180.05561.411
160.06251.587
140.07141.814
130.07691.954
120.08332.117
110.09092.309
100.10002.540
90.11112.822
80.12503.175

Some pitches sit close together across the two systems. 20 TPI is 1.270 mm, close to the 1.25 mm of M8. 32 TPI is 0.794 mm, close to the 0.8 mm of M5. A pitch gauge can tell these apart only over a long length of thread; the step-by-step method is in how to measure thread pitch.

Major, minor and pitch diameter

Every thread has three diameters. The major diameter is the largest, across the crests of a bolt or the roots of a nut. The minor diameter is the smallest, across the roots of a bolt or the crests of a nut. The pitch diameter lies between them, where the width of the thread equals the width of the groove.

Pitch diameter is the one that controls fit, because the flanks of bolt and nut touch there. Thread tolerance classes such as 6g and 2A are mainly limits on pitch diameter; see thread classes and fits.

Formulas for 60° metric and Unified threads

  • Pitch diameter: d2 = d − 0.6495 × P
  • Internal (nut) minor diameter: D1 = d − 1.0825 × P
  • External (bolt) minor diameter, metric: d3 = d − 1.2269 × P
  • Thread height of the basic triangle: H = 0.8660 × P

Worked example for M8 × 1.25: pitch diameter = 8 − 0.6495 × 1.25 = 7.188 mm, nut minor diameter = 6.647 mm, bolt minor diameter = 6.466 mm. For 1/4-20 UNC, with P = 1/20 = 0.050 in: pitch diameter = 0.250 − 0.6495 × 0.050 = 0.2175 in and basic nut minor diameter = 0.1959 in.

Pitch diameter is measured with a thread micrometer or with three wires over the thread. It cannot be measured with plain calipers.

How to read a thread size

A thread callout lists diameter, pitch, series and tolerance class, in that order. Two examples cover nearly everything on a drawing or a parts bin.

  • M8 × 1.25-6g: metric (M), 8 mm major diameter, 1.25 mm pitch, tolerance class 6g (external). A tapped hole would be M8 × 1.25-6H. The pitch is often left off for coarse threads: M8-6g.
  • 1/4-20 UNC-2A: 1/4 in major diameter, 20 threads per inch, Unified coarse series, class 2A (A = external, B = internal). Number sizes read the same way: #10-32 UNF-2B is a 0.190 in tapped hole with 32 TPI.
  • LH after the callout means left-hand. No suffix means right-hand.
  • Multi-start metric threads give lead and pitch: M16 × Ph3 P1.5 is a two-start thread with 3 mm lead and 1.5 mm pitch.

Pipe threads such as 1/2 NPT do not follow this pattern: the size is a nominal pipe size, not a measured diameter. See the NPT thread chart.

How to find the thread size of a bolt

Measure the major diameter with calipers, then measure the pitch with a gauge, and match both to the charts above. A bolt measuring 7.76 to 7.97 mm with crests 1.25 mm apart is M8 × 1.25. A bolt measuring about 0.245 in with 20 threads in one inch is 1/4-20 UNC.

  1. Clean the thread and measure across the crests with calipers. Bolts measure a little under nominal.
  2. Decide whether the reading is closer to a whole millimeter or to an inch fraction. The inch to mm chart helps.
  3. Check the pitch with a metric gauge and an inch gauge. The leaf that seats with no light along the full length is the pitch.
  4. For a tapped hole, measure the bore at the crests (the minor diameter) and compare it with the tap drill sizes on the tap drill chart.

For metric bolts, the wrench size is a quick check: M6 takes a 10 mm wrench, M8 a 13 mm and M10 a 16 or 17 mm. The bolt and wrench size chart lists all sizes.

Sources and standards

  • ASME B1.1, Unified inch screw threads (UN and UNR thread form)
  • ISO 261
  • ISO 262
  • ISO 68-1
  • ISO 965-1

General reference information. When a manufacturer, drawing or governing standard gives a value, that value takes precedence.

Related charts and guides

Common questions

What is the diameter of a #10 screw?

A #10 screw has a major diameter of 0.190 in (4.83 mm). Number sizes follow 0.060 in + 0.013 in × the number. #10 comes as #10-24 UNC (coarse) and #10-32 UNF (fine). The nearest metric size is M5, which is 5.0 mm with a 0.8 mm pitch and is not interchangeable.

What is the major diameter of 8-32 and 10-32?

The basic major diameter of #8-32 is 0.164 in (4.17 mm) and of #10-32 is 0.190 in (4.83 mm). A class 2A screw measures a few thousandths under that because of the allowance and tolerance. The tapped hole minor diameter is smaller, set by the tap drill: #29 for 8-32 and #21 for 10-32.

What is thread pitch?

Thread pitch is the distance between neighboring thread crests, measured along the axis. Metric threads give it in millimeters, for example 1.25 mm on M8. Inch threads give threads per inch instead; pitch = 25.4 ÷ TPI in millimeters, so 20 TPI equals a 1.270 mm pitch.

How do you read a metric thread size?

M8 × 1.25-6g means a metric ISO thread with 8 mm major diameter, 1.25 mm pitch and tolerance class 6g for a bolt. Internal threads use capital letters, such as 6H. If the pitch is missing, as in M8, the thread is ISO coarse. Fine threads always show the pitch, for example M8 × 1.

What thread size is a 10 mm bolt?

An M10 bolt has a 10 mm major diameter and a 1.5 mm coarse pitch. Fine options are M10 × 1.25 and M10 × 1. People also call an M6 bolt a 10 mm bolt because its ISO hex head takes a 10 mm wrench. Measure the shank: about 10 mm means M10, about 6 mm means M6.

How do you find the pitch diameter of a thread?

For 60° metric and Unified threads, pitch diameter = major diameter − 0.6495 × pitch. M8 × 1.25 gives 8 − 0.812 = 7.188 mm. 1/4-20 gives 0.250 − 0.0325 = 0.2175 in. On a real part it is measured with a thread micrometer or the three-wire method, not with plain calipers.

What is all thread?

All thread, or threaded rod, is bar threaded along its full length with no head. It is usually sold in UNC sizes such as 3/8-16 and 1/2-13 or metric coarse sizes such as M10 × 1.5 and M12 × 1.75. It is cut to length and used with nuts for hangers, anchors and clamps.

Arrow keys to move, Enter to open, Esc to close