MachinistCharts

Threads and tapping

NPT tap drill sizes and NPT thread chart

Short answer

Common NPT tap drill sizes without a reamer: 1/16 NPT 1/4 in, 1/8 NPT R (0.339 in), 1/4 NPT 7/16 in, 3/8 NPT 37/64 in, 1/2 NPT 23/32 in, 3/4 NPT 59/64 in, 1 NPT 1-5/32 in, 1-1/4 NPT 1-1/2 in, 1-1/2 NPT 1-47/64 in and 2 NPT 2-7/32 in. NPT threads taper 1:16 and have 27, 18, 14 or 11.5 TPI.

By the MachinistCharts editors · Updated · 7 min read

Tapered pipe tap, twist drill and threaded brass and iron pipe fittings on a workbench

Key takeaways

  • 1/8 NPT tap drill is R (0.339 in); some charts list 11/32 in.
  • 1/2 NPT is 14 TPI on a 0.840 in pipe OD; pipe sizes are nominal, not measured.
  • NPT tapers 1:16 on diameter, 3/4 in per foot, a half-angle of 1° 47′.
  • Hand-tight engagement is about 4 to 5 turns; wrench makeup adds about 3 threads.
  • NPT is 60°, BSP is 55°; at 1/2 and 3/4 in both have 14 TPI but they do not seal together.

NPT tap drill sizes

The common NPT tap drill sizes, drilling without a taper reamer, are: 1/16 NPT 1/4 in, 1/8 NPT R (0.339 in), 1/4 NPT 7/16 in, 3/8 NPT 37/64 in, 1/2 NPT 23/32 in, 3/4 NPT 59/64 in, 1 NPT 1-5/32 in, 1-1/4 NPT 1-1/2 in, 1-1/2 NPT 1-47/64 in and 2 NPT 2-7/32 in. These are shop-standard values; makers' charts differ by a size in places.

NPT sizeTap drill (no reamer)Decimal (in)Metric (mm)Also used
1/16 NPT1/4"0.25006.35D (0.2460 in)
1/8 NPTR0.33908.6111/32" (0.3438 in)
1/4 NPT7/16"0.437511.11—
3/8 NPT37/64"0.578114.689/16" (0.5625 in)
1/2 NPT23/32"0.718818.26—
3/4 NPT59/64"0.921923.42—
1 NPT1-5/32"1.156329.37—
1-1/4 NPT1-1/2"1.500038.10—
1-1/2 NPT1-47/64"1.734444.05—
2 NPT2-7/32"2.218856.36—

The "also used" column shows the alternative that some tap makers list: a D drill for 1/16 NPT, 11/32 in for 1/8 NPT and 9/16 in for 3/8 NPT. Use the size recommended by the tap maker when it is given. Decimal values for letter and fractional drills are on the drill size chart, for example letter R and 7/16 in.

A tapered pipe tap cuts more material as it goes deeper, so it needs more torque than a straight tap. Drilling, then taper reaming before tapping reduces tap load and gives a fuller thread; reamed holes use a smaller drill. Tap until a male fitting threads in hand-tight by about the L1 length in the table further down, or until an L1 plug gauge sits within one turn of flush.

NPT thread chart

NPT (National Pipe Taper) is the US tapered pipe thread defined in ASME B1.20.1. It has a 60° thread angle, a taper of 1:16 on diameter, and flattened crests and roots. Sizes from 1/16 to 2 in use 27, 18, 14 or 11.5 threads per inch.

ThreadTPIPitch (mm)Pipe OD (in)Pipe OD (mm)Tap drillDrill (in)
1/16-27 NPT270.9410.31257.941/4"0.2500
1/8-27 NPT270.9410.40510.29R0.3390
1/4-18 NPT181.4110.54013.727/16"0.4375
3/8-18 NPT181.4110.67517.1537/64"0.5781
1/2-14 NPT141.8140.84021.3423/32"0.7188
3/4-14 NPT141.8141.05026.6759/64"0.9219
1-11.5 NPT11.52.2091.31533.401-5/32"1.1563
1-1/4-11.5 NPT11.52.2091.66042.161-1/2"1.5000
1-1/2-11.5 NPT11.52.2091.90048.261-47/64"1.7344
2-11.5 NPT11.52.2092.37560.332-7/32"2.2188

The pipe OD is the outside diameter of the pipe, and the male thread measures close to it at its large end. A 1/8-27 NPT thread is a 1/8 in nominal pipe size with 27 threads per inch and an OD of 0.405 in (10.29 mm). For a 1/8 NPT tap, use an R drill, 0.339 in.

What does 1/2 NPT mean?

1/2 NPT means a National Pipe Taper thread for 1/2 in nominal pipe size: 14 threads per inch, a pipe OD of 0.840 in, and a taper of 1:16. A full callout is 1/2-14 NPT. The name refers to the pipe size, not to any diameter of the thread.

  • MPT, MNPT or MIP: male NPT thread (on the outside of a fitting).
  • FPT, FNPT or FIP: female NPT thread (inside a fitting or tapped hole).
  • 1-1/2 NPT: 1-1/2 in nominal pipe, 11.5 TPI, pipe OD 1.900 in (48.26 mm).

To identify a pipe thread, measure the male OD with calipers and count the threads per inch, then match both to the chart. A male thread measuring about 0.84 in with 14 TPI is 1/2 NPT; about 0.54 in with 18 TPI is 1/4 NPT. For female threads, measure the bore at the opening, which is a little smaller than the pipe OD. The general method is in how to measure thread pitch.

NPT taper and thread engagement

The NPT taper is 1 in 16 on diameter: the diameter changes by 1/16 in per inch of length, which is 0.75 in per foot. The half-angle of the taper is 1° 47′ to the axis. As the threads screw together they wedge tighter, which is what seals the joint.

ASME B1.20.1 defines the hand-tight engagement L1, how far a male thread enters by hand, and the effective thread length L2, the length of full thread on the pipe. Wrench makeup adds about 3 more threads beyond hand-tight.

SizeHand-tight engagement L1 (in)L1 in turnsEffective thread L2 (in)L2 (mm)
1/16 NPT0.16004.30.26116.6
1/8 NPT0.16154.40.26396.7
1/4 NPT0.22784.10.401810.2
3/8 NPT0.24004.30.407810.4
1/2 NPT0.32004.50.533713.6
3/4 NPT0.33904.70.545713.9
1 NPT0.40004.60.682817.3
1-1/4 NPT0.42004.80.706818.0
1-1/2 NPT0.42004.80.723518.4
2 NPT0.43605.00.756519.2

Hand-tight engagement is about 4 to 5 turns for every size. Typical practice is hand-tight plus 1.5 to 3 turns with a wrench, on threads sealed with PTFE tape or pipe dope. Over-tightening a tapered thread can split a female fitting, especially in cast iron, brass or aluminum. In a tapped hole, the full thread depth should be at least L2 so the male fitting can make up fully; see thread engagement length for straight threads.

NPT vs NPTF vs BSPT vs BSPP

NPT and NPTF are both 60° US tapered pipe threads with the same TPI; NPTF (Dryseal) controls crest and root truncation so the threads seal metal to metal without sealant. BSPT and BSPP are British Standard Pipe threads with a 55° Whitworth angle; BSPT is tapered and BSPP (G) is parallel.

ThreadStandardAngleFormHow it seals
NPTASME B1.20.160°Tapered 1:16On the thread, with PTFE tape or paste
NPTF (Dryseal)ASME B1.20.360°Tapered 1:16Metal to metal: crests and roots crush together
NPSMASME B1.20.160°ParallelDoes not seal on the thread; uses a gasket or seat
BSPT (R, Rc, Rp)ISO 7-155°Tapered 1:16 (Rp parallel)On the thread, with sealant
BSPP (G)ISO 228-155°ParallelBonded washer, O-ring or gasket

NPT and NPTF parts screw together, but the joint is dry-sealing only when both are NPTF; otherwise use sealant. NPSM is a straight thread that mates loosely with NPT and seals on a seat, as on swivel hose fittings.

NPT vs BSP

SizeNPT TPIBSP TPINPT OD (mm)BSP major dia (mm)Difference
1/8272810.299.728different TPI and angle
1/4181913.7213.157different TPI and angle
3/8181917.1516.662different TPI and angle
1/2141421.3420.955same TPI, different angle
3/4141426.6726.441same TPI, different angle
111.51133.4033.249different TPI and angle
1-1/411.51142.16—different TPI and angle
1-1/211.51148.26—different TPI and angle
211.51160.33—different TPI and angle

BSP major diameters from ISO 228-1. At 1/2 and 3/4 in, NPT and BSP share 14 TPI, so the threads start and run a turn or two before the 60° and 55° flanks fight. The joint can feel tight and still leak. Do not mix them: use an adapter.

3/8 BSP thread is 19 TPI with a major diameter of 16.662 mm; 3/8 NPT is 18 TPI on a 0.675 in (17.15 mm) pipe. BSPP is marked G, for example G1/4. BSPT is marked R for male taper, Rc for female taper and Rp for female parallel (ISO 7-1). The metric vs imperial threads guide covers Whitworth threads more broadly.

How to show NPT on a drawing

Call out an NPT thread as size, TPI and series: 1/4-18 NPT. Add NPTF for Dryseal threads. Add the tap drill and depth if the shop needs them, for example "7/16 DRILL × 0.75 DEEP, 1/4-18 NPT". Thread representation on drawings follows ASME Y14.6.

  • Specify the tap depth or the fitting gauge condition rather than a diameter: tapered threads are accepted with an L1 plug or ring gauge, not with calipers.
  • Show the taper on the drawing or use the NPT note; a tapered thread drawn parallel is still read as tapered when the callout says NPT.
  • For a straight pipe thread, write NPSM or G (BSPP) so the shop does not cut a taper.

For straight threads, the tap drill for every metric and inch size is on the tap drill chart, for example 1/4-20 and M10, and thread tolerances are explained in thread classes and fits. Tap styles, including pipe taps, are covered in types of taps.

Sources and standards

  • ASME B1.20.1
  • ASME B1.20.3
  • ISO 7-1
  • ISO 228-1
  • ASME Y14.6

General reference information. When a manufacturer, drawing or governing standard gives a value, that value takes precedence.

Related charts and guides

Common questions

What size drill bit for a 1/8 NPT tap?

Use an R drill (0.339 in, 8.61 mm) for a 1/8-27 NPT tap when drilling without a taper reamer. Some charts list 11/32 in (0.3438 in), which is slightly larger and makes the tap easier to turn. Tap until a male fitting threads in by hand about 4 to 4.5 turns.

What size drill for a 1/4 NPT tap?

Use a 7/16 in drill (0.4375 in, 11.11 mm) for a 1/4-18 NPT tap without a reamer. 1/4 NPT has 18 threads per inch on a 0.540 in pipe OD. Tap to a depth that lets a male fitting enter hand-tight about 4 turns, then make up with a wrench.

What size drill for a 3/8 NPT tap?

The common drill for a 3/8-18 NPT tap is 37/64 in (0.5781 in, 14.68 mm); some tap makers list 9/16 in (0.5625 in). 3/8 NPT has 18 threads per inch on a 0.675 in pipe OD. Follow the tap maker's chart when it gives a size.

What size drill bit for a 1/2 NPT tap?

Use a 23/32 in drill (0.7188 in, 18.26 mm) for a 1/2-14 NPT tap without a reamer. 1/2 NPT has 14 threads per inch and fits pipe with a 0.840 in (21.34 mm) outside diameter. Hand-tight engagement is about 0.320 in, roughly 4.5 turns.

What does NPT stand for in threads?

NPT stands for National Pipe Taper, the US standard tapered pipe thread in ASME B1.20.1. It has a 60° thread angle and a taper of 1 in 16 on diameter, so the joint seals as the threads wedge together, normally with PTFE tape or pipe dope. NPTF is the Dryseal version that seals without sealant.

What is MPT thread?

MPT means male pipe thread, normally male NPT; it is also written MNPT or MIP. FPT, FNPT or FIP is the female thread. A 1/2 in MPT fitting has a 1/2-14 NPT external thread that fits a 1/2 in FPT port. The size is the nominal pipe size, not the measured thread diameter.

How do you measure NPT thread size?

Measure the outside diameter of a male thread with calipers near its large end and count threads per inch, then match to an NPT chart. About 0.40 in with 27 TPI is 1/8 NPT, 0.54 in with 18 TPI is 1/4 NPT, 0.84 in with 14 TPI is 1/2 NPT. Do not round the diameter to a fraction; pipe sizes are nominal.

What is the difference between NPT and BSP threads?

NPT has a 60° thread angle and BSP a 55° Whitworth angle. Most sizes differ in TPI too: 1/8 NPT has 27 and 1/8 BSP 28; 1/4 and 3/8 NPT have 18 against 19. At 1/2 and 3/4 in both have 14 TPI, but the different angle still leaks. BSPP (G) is parallel and seals on a washer.

Arrow keys to move, Enter to open, Esc to close