6201 bearing dimensions
A 6201 bearing is 12 mm bore × 32 mm outside diameter × 10 mm wide (0.472 × 1.260 × 0.394 in). The sealed version is 6201-2RS; the shielded version is 6201-ZZ.
6201 at a glance
Boundary dimensions in millimetres and inches, and the common closure designations.
- Bore, d
- 12 mm 0.4724"
- Outside diameter, D
- 32 mm 1.2598"
- Width, B
- 10 mm 0.3937"
- Section height, (D − d)/2
- 10 mm 0.3937"
- Series
- 62 series light
- Bore code
- 01 01 = 12 mm
- Sealed, both sides
- 6201-2RS
- Shielded, both sides
- 6201-ZZ
- Open
- 6201 no closures; any version may add C3 for extra internal clearance
Reading the number 6201
Every deep groove ball bearing number follows the same pattern: type, dimension series and bore code, then suffixes.
Seals, shields and suffixes
Suffixes add closures and internal clearance. They do not change the boundary dimensions: a sealed and an open bearing of the same number are interchangeable in size.
| Suffix | Meaning | 6201 example |
|---|---|---|
| Open (no suffix) | No seals or shields. Can be relubricated, or run in an oil bath; the housing needs its own seal against dirt. | 6201 |
| Z | One metal shield, on one side only. | 6201-Z |
| ZZ, 2Z | Metal shields on both sides. Non-contact, so low friction; keeps out larger dirt. Usually greased for life. | 6201-ZZ |
| RS | One rubber contact seal, on one side only. | 6201-RS |
| 2RS, 2RS1, 2RSH, 2RSR, DDU, LLU | Rubber contact seals on both sides. Better than shields against fine dirt and splashing water, with a little more friction. Usually greased for life. | 6201-2RS |
| C3 | Radial internal clearance greater than normal (CN). Used with tight shaft or housing fits, or where the inner ring runs hotter than the outer ring. | 6201-2RS C3 |
6201 in other brands
The sealed and shielded versions as each maker writes them. All share the same boundary dimensions.
| Maker | Sealed both sides | Shielded both sides |
|---|---|---|
| SKF | 6201-2RSH | 6201-2Z |
| FAG (Schaeffler) | 6201-2RSR | 6201-2ZR |
| NSK | 6201DDU | 6201ZZ |
| NTN | 6201LLU | 6201ZZ |
| Koyo (JTEKT) | 6201-2RS | 6201ZZ |
| Timken | 6201-2RS | see catalogue |
Seal designs and suffixes vary by maker, size range and product generation, for example contact versus low-friction seals. Confirm the exact designation in the maker's catalogue before ordering.
Same 12 mm bore, other series
Bearings that fit the same shaft. A heavier series carries more load in a bigger housing bore; a thin-section series saves space and weight.
62 series
Common questions
What size is a 6201 bearing?
12 mm bore, 32 mm outside diameter and 10 mm wide, which is 0.472 × 1.260 × 0.394 in.
What does 2RS mean on a 6201 bearing?
6201-2RS has rubber contact seals on both sides. 6201-ZZ (also written 6201-2Z) has metal shields on both sides. Both have the same 12 × 32 × 10 mm dimensions.
Is 6201-2RS the same as 6201-ZZ?
They are the same size and interchangeable in a housing. The sealed 6201-2RS keeps out fine dirt and water better; the shielded 6201-ZZ runs with less friction.
What is the SKF equivalent of 6201-2RS?
SKF writes it 6201-2RSH; FAG 6201-2RSR, NSK 6201DDU, NTN 6201LLU and Koyo 6201-2RS. Check the maker's catalogue for the exact seal type.
What does the number 6201 mean?
6 is the deep groove ball bearing type, 2 is the light dimension series, and 01 = 12 mm (codes 00 to 03 are fixed: 10, 12, 15 and 17 mm).
Which bearings have the same bore as 6201?
6801, 6901, 6001, 6301 also have a 12 mm bore, with different outside diameters and widths.