MachinistCharts

Bearings

Static vs dynamic load ratings and bearing life calculation

Short answer

In static vs dynamic load terms, a bearing's dynamic load rating C is the load it can carry for a rated life (L10) of one million revolutions, and its static load rating C0 is the load that causes a tiny permanent dent at standstill. Ball bearing life is L10 = (C/P)³ million revolutions, where P is the equivalent load; roller bearings use the exponent 10/3.

By the MachinistCharts editors · Updated · 7 min read

Sectioned ball bearing under a press ram on a steel test fixture

Key takeaways

  • C (dynamic load rating) gives an L10 life of exactly one million revolutions; C0 (static load rating) limits load at standstill or slow rotation.
  • Ball bearing life: L10 = (C/P)³ million revolutions. Roller bearings use the exponent 10/3.
  • Hours of life: L10h = 10⁶ / (60 × n) × (C/P)^p, with n in rpm.
  • Doubling the load on a ball bearing cuts its rated life to one eighth.
  • Combined loads become one equivalent load: P = X × Fr + Y × Fa, with X and Y from the maker's table.

Static vs dynamic load: what the terms mean

A static load is a load that does not change with time and acts on a part that is not moving. A dynamic load changes in size, direction or position over time, or acts on a moving or rotating part. In bearings, the static vs dynamic load distinction decides which rating you check: the static load rating C0 for a bearing that is stationary, oscillating or turning very slowly, and the dynamic load rating C for a bearing that rotates.

  • Static loading means the load is applied while the bearing is not rotating. The risk is permanent dents (brinelling) in the raceways.
  • Dynamic loading means the bearing rotates under load. The risk is rolling contact fatigue: flaking of the raceway after many millions of stress cycles.

Both ratings are listed in every bearing catalog. They vary between makers for the same bearing number, so this guide gives the formulas, not ratings for specific bearings. Bearing sizes are on the bearing size chart.

Dynamic load rating C

The basic dynamic load rating C is the constant radial load (axial load for thrust bearings) under which a group of identical bearings reaches a basic rating life of one million revolutions, as defined in ISO 281. It is not a load the bearing should actually run at: at P = C the rated life is only one million revolutions, which is about 11 hours at 1,500 rpm.

Dynamic load capacity grows with bearing size and series. For the same 25 mm bore, a 6305 (medium series) has a higher C than a 6205 (light series), which has a higher C than a 6005 (extra-light series). Roller bearings have higher C than ball bearings of the same envelope; see types of bearings.

Bearing life equation: L10

The basic rating life L10 is the life that 90 % of a large group of identical bearings will reach or exceed before the first sign of fatigue. The bearing life equation from ISO 281 is:

L10 = (C/P)^p million revolutions

  • C = basic dynamic load rating, N
  • P = equivalent dynamic bearing load, N
  • p = 3 for ball bearings, 10/3 for roller bearings

For life in operating hours at a constant speed n in rpm:

L10h = 10⁶ / (60 × n) × (C/P)^p hours

The exponent makes life very sensitive to load. This table is computed from the formula and applies to any bearing.

C/PBall bearing L10, million rev (p = 3)Roller bearing L10, million rev (p = 10/3)Ball bearing L10h at 1,000 rpm, hours
11.001.0016.7
28.0010.1133
327.038.9450
464.01021,067
51252142,083
62163923,600
85121,0248,533
101,0002,15416,667
121,7283,95628,800

L10 is a statistical value: half of the bearings in a group last roughly five times L10. It also assumes good lubrication, clean conditions and correct mounting. ISO 281 adds a modified rating life, Lnm = a1 × aISO × L10, where a1 adjusts for reliability other than 90 % and aISO accounts for lubrication, contamination and the material fatigue limit. aISO can be well above or well below 1, which is why clean, well-lubricated bearings often outlast their L10 and contaminated ones fail early.

ReliabilityLife designationReliability factor a1 (ISO 281:2007)
90 %L101
95 %L50.64
96 %L40.55
97 %L30.47
98 %L20.37
99 %L10.25

Equivalent dynamic load P = X·Fr + Y·Fa

When a bearing carries both radial and axial load, the two are combined into one equivalent dynamic load P, which is the pure radial load that would give the same life:

P = X × Fr + Y × Fa

  • Fr = radial load, N; Fa = axial load, N
  • X = radial load factor; Y = axial load factor

For a single row deep groove ball bearing, the calculation uses a limit value e from the maker's table. If Fa/Fr is less than or equal to e, the axial load is ignored and P = Fr. If Fa/Fr is greater than e, X = 0.56 and Y is taken from the table. In ISO 281, e and Y for deep groove ball bearings depend on the ratio of axial load to static load rating C0: as that ratio rises, e rises from about 0.19 to 0.44 and Y falls from 2.30 to 1.00. Angular contact, tapered roller and spherical roller bearings have their own X, Y and e values in each maker's catalog.

Variable loads and speeds

If the load changes in steps, use a mean equivalent load. For ball bearings: P = (U1 × P1³ + U2 × P2³ + …)^(1/3), where U is the fraction of total revolutions spent at each load. For example, half the revolutions at 1,000 N and half at 3,000 N give P = 2,410 N, higher than the simple average of 2,000 N because the heavier load does most of the damage. For roller bearings use the exponent 10/3 in place of 3.

Bearing life calculation: worked examples

The values below are hypothetical, chosen to show the method. For a real bearing, take C, C0, e, X and Y from the maker's catalog for that exact part number.

Example 1: pure radial load

A hypothetical deep groove ball bearing has C = 14,000 N. It carries a radial load Fr = 2,000 N and no axial load, at n = 1,500 rpm. With no axial load, P = Fr = 2,000 N.

  • C/P = 14,000 / 2,000 = 7.00
  • L10 = 7.00³ = 343 million revolutions
  • L10h = 10⁶ / (60 × 1,500) × 343 = 3,811 hours

Example 2: combined radial and axial load

The same bearing now also carries Fa = 800 N axial load. Suppose the maker's table for this bearing and load gives e = 0.28, X = 0.56 and Y = 1.55. Fa/Fr = 0.40, which is greater than e, so the axial load counts.

  • P = 0.56 × 2,000 + 1.55 × 800 = 2,360 N
  • C/P = 5.93; L10 = 5.93³ = 209 million revolutions
  • L10h = 2,320 hours at 1,500 rpm

An axial load of 40 % of the radial load cut the rated life from 3,811 to 2,320 hours.

Example 3: double the load

Doubling the pure radial load to 4,000 N gives C/P = 3.50 and L10 = 42.9 million revolutions, or 476 hours: one eighth of example 1, because life scales with the cube of the load ratio.

Life in hours is inversely proportional to speed: double the rpm, half the hours. For the example 1 bearing:

Speed, rpmL10h, hours (C/P = 7.00, ball bearing)
10057,167
50011,433
1,0005,717
1,5003,811
3,0001,906
6,000953

These calculations ignore fits, shaft deflection, temperature and lubrication; correct bearing fits and clearance are needed to reach calculated life.

What is static load capacity?

Static load capacity is the basic static load rating C0: the load that produces a calculated contact stress at the most heavily loaded rolling element contact of 4,200 MPa for most ball bearings, 4,600 MPa for self-aligning ball bearings and 4,000 MPa for roller bearings (ISO 76). At this stress the total permanent deformation of rolling element and raceway is about 0.0001 of the rolling element diameter, small enough not to harm normal operation.

C0 applies when the bearing is stationary, oscillating, rotating very slowly, or hit by heavy shock loads while running. Exceeding it dents the raceways, which shows up as noise and vibration once the bearing turns.

Static equivalent load

Combined static loads are converted to a static equivalent load P0 = X0 × Fr + Y0 × Fa. For a single row deep groove ball bearing, X0 = 0.6 and Y0 = 0.5, and P0 is never taken as less than Fr.

Static safety factor s0

The static safety factor is s0 = C0 / P0. An s0 of 1 means the peak load just reaches the static rating. Typical guidance from bearing makers is around 1 for normal duty, 2 or more where quiet, smooth running matters or shock loads are expected, and lower values only for smooth, non-critical slow motion. The exact recommended values differ by maker and bearing type.

Radial load vs axial load

A radial load acts at right angles to the shaft; an axial load acts along it. Radial load comes from gear tooth forces, belt and chain pull, and the weight of rotors and pulleys. Axial load comes from helical gears, thrust from pumps and fans, preload and thermal expansion of the shaft between fixed bearings.

  • Bearing for radial load: deep groove ball, cylindrical roller and needle roller bearings.
  • Bearing for axial load: thrust ball and thrust roller bearings.
  • Combined load: deep groove ball for moderate axial load; angular contact ball or tapered roller pairs for heavy axial load.

Belt tension is a common hidden radial load. A belt or chain drive loads the bearings with the sum of the tight-side and slack-side tension, which is larger than the transmitted force alone, so check the drive maker's data when calculating P. Bearing selection by load direction is covered in types of bearings, and the materials that affect load rating in ball bearing materials.

Sources and standards

  • ISO 281
  • ISO 76

General reference information. When a manufacturer, drawing or governing standard gives a value, that value takes precedence.

Related charts and guides

Common questions

What is the difference between static and dynamic load?

A static load is constant and acts on a part that is not moving. A dynamic load varies with time or acts on a moving or rotating part. For bearings, the static load rating C0 limits load at standstill or slow rotation, and the dynamic load rating C is used to calculate fatigue life when the bearing rotates.

What is static load capacity of a bearing?

Static load capacity, the basic static load rating C0, is the load that produces a contact stress of 4,200 MPa in a ball bearing (4,000 MPa in a roller bearing) at the most heavily loaded contact, per ISO 76. It causes a permanent deformation of about 0.0001 of the rolling element diameter.

What is the dynamic load rating of a bearing?

The basic dynamic load rating C is the constant load under which 90 % of a group of identical bearings reach one million revolutions before fatigue, per ISO 281. It is used in the life equation L10 = (C/P)³ for ball bearings. It is not a safe working load, because at P = C the life is only one million revolutions.

How do you calculate bearing life?

Use L10 = (C/P)^p million revolutions, with p = 3 for ball bearings and 10/3 for roller bearings. Convert to hours with L10h = 10⁶ / (60 × n) × (C/P)^p, where n is speed in rpm. For example, a ball bearing at C/P = 7 and 1,500 rpm has L10 = 343 million revolutions, or about 3,811 hours.

What does L10 life mean?

L10 life is the number of revolutions or hours that 90 % of a large group of identical bearings will reach or exceed before the first sign of rolling contact fatigue. Ten percent may fail sooner. It assumes good lubrication and cleanliness. ISO 281 also gives a modified life that adjusts for reliability, lubrication and contamination.

How does load affect bearing life?

Ball bearing life varies with the cube of the load ratio. Doubling the load cuts rated life to one eighth; halving it multiplies life by eight. For roller bearings the exponent is 10/3, so halving the load multiplies life by about ten. Small load reductions therefore give large life gains.

What is a radial load on a bearing?

A radial load acts at right angles to the shaft axis, such as belt pull, gear tooth force or rotor weight. Deep groove ball, cylindrical roller and needle roller bearings are designed mainly for radial load. Load along the shaft is called axial or thrust load and needs a bearing type rated for it.

Arrow keys to move, Enter to open, Esc to close