6009 bearing dimensions
A 6009 bearing is 45 mm bore × 75 mm outside diameter × 16 mm wide (1.772 × 2.953 × 0.630 in). The sealed version is 6009-2RS; the shielded version is 6009-ZZ.
6009 at a glance
Boundary dimensions in millimetres and inches, and the common closure designations.
- Bore, d
- 45 mm 1.7717"
- Outside diameter, D
- 75 mm 2.9528"
- Width, B
- 16 mm 0.6299"
- Section height, (D − d)/2
- 15 mm 0.5906"
- Series
- 60 series extra-light
- Bore code
- 09 09 × 5 = 45 mm
- Sealed, both sides
- 6009-2RS
- Shielded, both sides
- 6009-ZZ
- Open
- 6009 no closures; any version may add C3 for extra internal clearance
Reading the number 6009
Every deep groove ball bearing number follows the same pattern: type, dimension series and bore code, then suffixes.
Seals, shields and suffixes
Suffixes add closures and internal clearance. They do not change the boundary dimensions: a sealed and an open bearing of the same number are interchangeable in size.
| Suffix | Meaning | 6009 example |
|---|---|---|
| Open (no suffix) | No seals or shields. Can be relubricated, or run in an oil bath; the housing needs its own seal against dirt. | 6009 |
| Z | One metal shield, on one side only. | 6009-Z |
| ZZ, 2Z | Metal shields on both sides. Non-contact, so low friction; keeps out larger dirt. Usually greased for life. | 6009-ZZ |
| RS | One rubber contact seal, on one side only. | 6009-RS |
| 2RS, 2RS1, 2RSH, 2RSR, DDU, LLU | Rubber contact seals on both sides. Better than shields against fine dirt and splashing water, with a little more friction. Usually greased for life. | 6009-2RS |
| C3 | Radial internal clearance greater than normal (CN). Used with tight shaft or housing fits, or where the inner ring runs hotter than the outer ring. | 6009-2RS C3 |
6009 in other brands
The sealed and shielded versions as each maker writes them. All share the same boundary dimensions.
| Maker | Sealed both sides | Shielded both sides |
|---|---|---|
| SKF | 6009-2RSH | 6009-2Z |
| FAG (Schaeffler) | 6009-2RSR | 6009-2ZR |
| NSK | 6009DDU | 6009ZZ |
| NTN | 6009LLU | 6009ZZ |
| Koyo (JTEKT) | 6009-2RS | 6009ZZ |
| Timken | 6009-2RS | see catalogue |
Seal designs and suffixes vary by maker, size range and product generation, for example contact versus low-friction seals. Confirm the exact designation in the maker's catalogue before ordering.
Same 45 mm bore, other series
Bearings that fit the same shaft. A heavier series carries more load in a bigger housing bore; a thin-section series saves space and weight.
| Bearing | Series | OD | Width | Section | vs 6009 |
|---|---|---|---|---|---|
| 6809 | thin-section | 58 mm | 7 mm | 6.5 mm | −17 mm OD, −9 mm wide |
| 6909 | thin-section | 68 mm | 12 mm | 11.5 mm | −7 mm OD, −4 mm wide |
| 6009 | extra-light | 75 mm | 16 mm | 15 mm | this bearing |
| 6209 | light | 85 mm | 19 mm | 20 mm | +10 mm OD, +3 mm wide |
| 6309 | medium | 100 mm | 25 mm | 27.5 mm | +25 mm OD, +9 mm wide |
60 series
Common questions
What size is a 6009 bearing?
45 mm bore, 75 mm outside diameter and 16 mm wide, which is 1.772 × 2.953 × 0.630 in.
What does 2RS mean on a 6009 bearing?
6009-2RS has rubber contact seals on both sides. 6009-ZZ (also written 6009-2Z) has metal shields on both sides. Both have the same 45 × 75 × 16 mm dimensions.
Is 6009-2RS the same as 6009-ZZ?
They are the same size and interchangeable in a housing. The sealed 6009-2RS keeps out fine dirt and water better; the shielded 6009-ZZ runs with less friction.
What is the SKF equivalent of 6009-2RS?
SKF writes it 6009-2RSH; FAG 6009-2RSR, NSK 6009DDU, NTN 6009LLU and Koyo 6009-2RS. Check the maker's catalogue for the exact seal type.
What does the number 6009 mean?
6 is the deep groove ball bearing type, 0 is the extra-light dimension series, and 09 × 5 = 45 mm (from 04 up, multiply by 5).
Which bearings have the same bore as 6009?
6809, 6909, 6209, 6309 also have a 45 mm bore, with different outside diameters and widths.