How to use a torque wrench correctly
How to use a torque wrench: set the target torque, fit the socket square on the fastener, hold the handle at the grip mark and pull slowly at 90° until it clicks or reads the target, then stop. ISO 6789 allows ±4 % error for most wrenches and recommends calibration every 12 months or 5,000 cycles.

Key takeaways
- Pull slowly at the grip mark, at 90° to the handle, and stop at the first click.
- ISO 6789 allows ±4 % deviation for most wrenches, ±6 % for some designs and wrenches of 10 N·m or less.
- Recalibrate every 12 months or 5,000 cycles, whichever comes first, or after a drop or overload.
- With an in-line adapter, set the wrench to Tw = Te × L ÷ (L + E); a crowfoot at 90° needs no correction.
- Use a torque wrench between 20 % and 100 % of its range; store click wrenches at the lowest setting.
How to use a torque wrench
To use a torque wrench, set the target torque, fit the socket square on the fastener, hold the handle at its grip mark and pull smoothly at 90° to the handle until the wrench clicks or the reading reaches the target. Stop at the first click. The whole job is to apply a known force at a known distance.
- Find the specification. Use the equipment maker's torque and note whether it is for dry or oiled threads. For a generic starting point use the bolt torque chart.
- Prepare the threads. Clean, undamaged threads give repeatable results. Lubricate only if the specification says so, because lubricant changes the clamp load at a given torque. See bolt torque formula.
- Run the fastener down. Turn it to snug by hand or with an ordinary wrench. A torque wrench is a measuring tool, not a breaker bar.
- Set the wrench to the target torque in the units the specification uses.
- Pull, do not jerk. Hold the handle at the marked grip point, keep the wrench square to the fastener and pull slowly and steadily, perpendicular to the handle.
- Stop at the click (click type) or at the reading (beam or digital). Do not pull past it or click twice.
- Follow the pattern on multi-bolt joints, in two or three passes. See bolt torque sequence.
- Store it correctly. Turn a click wrench down to the lowest marked setting after use, but not below it.
Most wrenches are calibrated with the force applied at the grip mark. On many click wrenches, pulling at a different point changes the torque at which the mechanism releases, so the torque at the fastener no longer matches the setting.
Types of torque wrench: click, beam and digital
The three common types are the click (micrometer) wrench, the beam wrench and the digital (electronic) wrench. All three measure the same thing; they differ in how they show it and how easily they drift out of calibration.
| Type | How it signals | Strengths | Limits |
|---|---|---|---|
| Click (micrometer) | Spring-loaded mechanism releases with a click and a small jump in the handle | Fast, repeatable, no need to watch a scale | Spring must be calibrated; must be stored at the lowest setting; overshoot if jerked |
| Beam (deflecting beam) | Pointer moves over a scale as the beam bends | Simple, cheap, rarely drifts, reads both directions | Must be read square-on; hard to read in tight spaces |
| Dial | Needle on a dial gauge, often with a peak memory needle | Accurate, shows the peak value | Bulky; dial can be damaged by impact |
| Digital (electronic) | Display, beep, light or vibration at the target | Unit switching, peak hold, often angle measurement and data logging | Needs batteries; electronics dislike drops and solvents |
| Split beam | Click mechanism that does not load the spring at rest | No need to wind down for storage | Usually coarser setting increments |
| Slipping (cam-over) | Slips at the set torque and cannot over-tighten | Production work, small fasteners | Usually preset, not adjustable by the user |
What type of torque wrench is most accurate?
Accuracy is set by calibration class, not by type alone. Good click, dial and digital wrenches commonly meet ±4 % under ISO 6789, and many electronic wrenches are specified tighter by their makers. In practice the user is the biggest error: jerking the handle, pulling off-angle or holding the wrong point adds more error than the tool.
How to set and read a click torque wrench
To set a click torque wrench, release the handle lock, turn it until the main scale and the handle (thimble) scale add up to the target, then lock it again. The main scale gives the coarse value and the thimble gives the fine increments.
- Release the lock: pull the locking collar back or turn the knob at the end of the handle.
- Turn the handle until the zero on the thimble lines up with the main-scale line just below your target. Example: target 46 ft-lb, set the main scale to 40.
- Add the fine increments by turning further until the thimble number on the center line reads the remainder, 6 in this example.
- Lock the handle so the setting cannot move while you work.
Check which scale you are reading. Most wrenches carry two scales, for example ft-lb on one side and N·m on the other, and the thimble increments differ between them. To convert a specification, use the torque converter: 1 ft-lb = 1.3558 N·m and 1 N·m = 8.851 in-lb.
Choosing the size of torque wrench
Pick a wrench whose working range puts your target between about 20 % and 100 % of its maximum, and ideally in the middle. ISO 6789 calibrates wrenches at 20 %, 60 % and 100 % of capacity, so below 20 % the accuracy is not verified. Small fasteners such as M5 and M6 need an in-lb or small N·m wrench; an M10 class 8.8 bolt at 50 N·m (37 ft-lb) suits a 3/8 or 1/2 in drive wrench.
Torque wrench accuracy and calibration
ISO 6789 allows most click and indicating torque wrenches a deviation of ±4 % of reading, and ±6 % for some designs and for small wrenches with a maximum of 10 N·m or less. The standard recommends recalibration every 12 months or every 5,000 cycles, whichever comes first.
ISO 6789-1 sorts hand torque tools into Type I (indicating: beam, dial, electronic) and Type II (setting: click, cam-over), each with several classes, and sets the permissible deviation for each. ISO 6789-2 sets the calibration method and the measurement uncertainty for calibration labs. A calibration certificate to ISO 6789-2 lists the readings at 20 %, 60 % and 100 % of the range.
When to calibrate a torque wrench
- Every 12 months or 5,000 cycles, whichever comes first, per ISO 6789-1, unless your quality system sets a different interval.
- After the wrench is dropped, overloaded past its maximum or used as a breaker bar.
- After any repair or adjustment to the mechanism.
- Before critical work if the wrench has been stored wound up for a long time.
How to check a torque wrench at home
You can check, though not calibrate, a wrench with a known weight. Clamp the square drive in a vise with the handle horizontal, hang a known mass from the grip mark and measure the distance from the center of the square drive to the hanging point. Torque = mass × 9.80665 × distance. A 10 kg mass at 0.5 m gives 49.0 N·m; a 20 lb weight at 2 ft gives 40 ft-lb. Set the wrench to that value: it should click as the weight is lowered gently onto it. If it is off by more than the ±4 % tolerance, send it to a calibration lab that can issue an ISO 6789-2 certificate.
Torque wrench extension and crowfoot formula
An adapter that lengthens the wrench along its axis, such as a crowfoot or offset head, increases the torque at the fastener. Set the wrench to Tw = Te × L ÷ (L + E), where Te is the torque you need at the fastener, L is the wrench length from the grip mark to the center of the square drive, and E is the added length measured along the wrench.
Example: you need 50 N·m with a 400 mm wrench and a crowfoot that adds 60 mm in line. Set the wrench to 50 × 400 ÷ (400 + 60) = 43.5 N·m. Leaving it at 50 N·m would apply 57.5 N·m to the fastener.
Wrench settings for 100 N·m at the fastener
| Wrench length L | E = 25 mm | E = 50 mm | E = 75 mm | E = 100 mm |
|---|---|---|---|---|
| 300 mm | 92.3 | 85.7 | 80.0 | 75.0 |
| 450 mm | 94.7 | 90.0 | 85.7 | 81.8 |
| 600 mm | 96.0 | 92.3 | 88.9 | 85.7 |
- Crowfoot at 90°: if the crowfoot points at right angles to the wrench, the effective length does not change (E = 0) and no correction is needed. This is the easiest way to use a crowfoot.
- Straight socket extensions: an extension bar in line with the square drive, at right angles to the handle, does not change the lever length and needs no correction. A long thin bar may twist, but the torque delivered is the same once motion stops.
- Universal joints: keep the angle small. Large angles add friction and make the reading unreliable.
- Handle extensions: a cheater pipe on the handle changes where you pull, which upsets the calibration of most click wrenches. Do not use one on a torque wrench.
The same correction applies in any units, so use it with ft-lb or in-lb as well.
Torque-angle tightening and torque-to-yield bolts
Torque-angle tightening means tightening to a snug torque and then turning the fastener through a set angle, such as 90°. Because rotation sets bolt stretch directly, it gives a more consistent clamp load than torque alone.
Use an angle gauge (a dial or digital disc between the wrench and socket, with an arm braced against a fixed part) or a digital torque wrench with angle measurement. Mark the fastener and a fixed point with paint as a visual check. Turn in one continuous motion where the procedure allows; stopping and restarting adds friction scatter.
Torque-to-yield (TTY) bolts
Torque-to-yield bolts are tightened into their yield zone by the angle step, so they stretch permanently. That gives a very uniform clamp load, which is why engine makers use them for cylinder heads, main bearing caps and connecting rods. Most TTY bolts are single-use: a stretched bolt has a reduced section and may neck or break on reuse. Follow the maker's torque, angle and replacement instructions exactly.
Turn-of-nut for structural bolts
Structural steel uses the same idea. Under the RCSC Specification for Structural Joints, with both faces normal to the bolt axis, the nut is turned from snug-tight by 1/3 turn for bolt lengths up to 4 diameters, 1/2 turn for over 4 up to 8 diameters, and 2/3 turn for over 8 up to 12 diameters.
The relationship between torque, preload and stretch is explained in bolt preload and clamp load. For calculated torque figures by size and grade, see the bolt torque calculator, the M8, M10 and M12 pages, or 3/8 in and 1/2 in bolts. Wheel nuts are covered in lug nut torque.
Sources and standards
- ISO 6789-1
- ISO 6789-2
- RCSC Specification for Structural Joints
General reference information. When a manufacturer, drawing or governing standard gives a value, that value takes precedence.
Related charts and guides
Common questions
How do you use a torque wrench properly?
Set the wrench to the specified torque, run the fastener down to snug, fit the socket fully on the fastener, hold the handle at the grip mark and pull slowly and steadily at 90° to the handle. Stop at the first click or when the reading reaches the target, and tighten multi-bolt joints in a star pattern.
How do you set a torque wrench?
Release the handle lock, turn it until the main scale shows the line just below the target, then keep turning until the thimble scale adds the remainder, for example 40 on the main scale plus 6 on the thimble for 46 ft-lb. Lock the handle and check you are reading the correct units scale.
How often should a torque wrench be calibrated?
ISO 6789-1 recommends recalibration every 12 months or 5,000 cycles, whichever comes first. Calibrate sooner after a drop, an overload past maximum, use as a breaker bar or any repair. A calibration to ISO 6789-2 checks readings at 20 %, 60 % and 100 % of the wrench's range.
How accurate is a click torque wrench?
ISO 6789 allows a click torque wrench a deviation of ±4 % of the reading for most models and ±6 % for some designs and wrenches with a maximum of 10 N·m or less. Accuracy is only verified between 20 % and 100 % of the wrench's capacity, so avoid using it below 20 %.
How much torque do you lose with an extension?
A straight socket extension in line with the square drive does not change the torque applied. An adapter that lengthens the wrench along its axis, such as a crowfoot pointing straight out, increases the torque: set the wrench to Te × L ÷ (L + E). A crowfoot turned at 90° to the handle needs no correction.
How do you test a torque wrench at home?
Clamp the square drive in a vise with the handle level, hang a known weight at the grip mark and measure the distance to the drive center. Torque equals weight times distance, for example 20 lb at 2 ft is 40 ft-lb. The wrench set to that value should click; a lab calibration is still needed for certification.
What is torque-angle tightening?
Torque-angle tightening means tightening to a snug torque and then rotating the fastener a specified angle, such as 90°, with an angle gauge. Rotation controls bolt stretch more directly than torque, so clamp load is more consistent. Torque-to-yield bolts use this method and are usually single-use.