# Tool steel grades: classes, common grades and hardness

Short answer: Tool steel grades are named by an AISI letter for the class and a number for the grade. W, O and A mean water, oil and air hardening; D is high-carbon high-chromium; S shock resisting; H hot work; M and T high speed; P mold steel. Typical working hardness: D2 58–62 HRC, A2 and O1 57–62, S7 54–58, H13 44–52, M2 62–65.

## Key takeaways

- The AISI letter gives the tool steel class: W, O, A by quench medium; D, M, T by alloy; S, H, P by application.
- D2 has the highest wear resistance of the common cold-work steels; A2 is tougher; O1 is easiest to machine and heat treat.
- Typical working hardness: D2 58–62 HRC, A2 and O1 57–62 HRC, S7 54–58 HRC, H13 44–52 HRC, M2 62–65 HRC.
- P20 mold steel is supplied pre-hardened, typically about 28–32 HRC, and machined without later heat treatment.
- Hardness values are typical; the supplier's heat-treatment data and the mill certificate decide.

## What is tool steel?

Tool steel is a high-quality carbon or alloy steel made to be hardened and used for cutting, forming, punching and molding other materials. Most tool steels contain about 0.5–1.5 % carbon plus carbide-forming elements such as chromium, molybdenum, tungsten and vanadium, and work at about 45–65 HRC after heat treatment.

What separates tool steel from ordinary carbon steel is control: tighter chemistry, cleaner steelmaking, and alloying chosen for one job, such as wear resistance, toughness, hot hardness or low distortion in hardening. Tool steels are bought annealed (soft enough to machine), then hardened and tempered, and finished by grinding or EDM. Some, such as P20, are sold pre-hardened.

In the US, tool steels are classified by AISI letter and number and specified under ASTM A681 (alloy tool steels), ASTM A600 (high-speed steels) and ASTM A686 (carbon, water-hardening tool steels). The letter tells you the class; the number identifies the grade within it. 4140 is sometimes called a "tool steel" because it is used for tool holders and fixtures, but it is a low-alloy steel, covered in [carbon steel grades](https://machinistcharts.com/guides/carbon-steel-grades/).

## Tool steel grades chart: AISI classes

AISI groups tool steel grades into classes named by a letter. The letter refers to the quench medium (W, O, A), the alloy type (D, M, T), or the application (S, H, P).

| Letter | Meaning | Class | Example grades | Main property |
|---|---|---|---|---|
| W | Water hardening | Plain high-carbon tool steel | W1, W2 | Low cost, hard skin, shallow hardening |
| O | Oil hardening | Cold work | O1, O2, O6 | Easy heat treatment, good machinability |
| A | Air hardening | Cold work, medium alloy | A2, A6 | Low distortion, balanced wear and toughness |
| D | High carbon, high chromium | Cold work | D2, D3 | Highest wear resistance of the cold-work steels |
| S | Shock resisting | Impact tools | S1, S5, S7 | Highest toughness |
| H | Hot work | Chromium, tungsten or molybdenum types | H11, H13, H21 | Strength and heat-check resistance at temperature |
| M | Molybdenum high speed | High-speed steel (HSS) | M2, M4, M42 | Hot hardness at the cutting edge |
| T | Tungsten high speed | High-speed steel (HSS) | T1, T15 | Hot hardness, wear resistance |
| P | Plastic mold | Mold steels | P20, P21 | Machinable pre-hardened, polishes well |
| L | Low alloy | Special purpose | L2, L6 | Toughness in tool and machine parts |

The cold-work classes O, A and D cover most dies, punches and shop tools that run at room temperature. H steels are for tools that touch hot metal. M and T steels are for cutting tools. S steels are for tools that are struck.

## Types of tool steel and what they are used for

### Water-hardening (W)

W1 is essentially a plain high-carbon steel, made in several carbon classes around 1 % carbon. It needs a water or brine quench, hardens only to a shallow depth and distorts more than alloy grades, but it is the cheapest tool steel and gives a very hard skin over a tough core.

### Cold-work (O, A, D)

Cold-work tool steels make tools that cut or form material at room temperature. [O1](https://machinistcharts.com/material/o1-tool-steel/) is the easiest to heat treat. [A2](https://machinistcharts.com/material/a2-tool-steel/) contains about 5 % chromium and hardens in still air with little movement. [D2](https://machinistcharts.com/material/d2-tool-steel/) contains about 1.5 % carbon and 12 % chromium, which form a large volume of hard chromium carbides for wear resistance. D3 is a higher-carbon, oil-hardening D grade.

### Shock-resisting (S)

S7 is the common shock-resisting tool steel: about 0.5 % carbon with chromium and molybdenum. The lower carbon gives high impact toughness at a working hardness of typically 54–58 HRC. It is air hardening in moderate sections, which keeps distortion low.

### Hot-work (H)

[H13](https://machinistcharts.com/material/h13-tool-steel/) is a 5 % chromium hot-work steel with molybdenum and vanadium. It keeps strength at high temperature and resists heat checking, the fine cracking caused by repeated heating and cooling. It is run softer than cold-work steels, typically 44–52 HRC, for toughness.

### High-speed (M and T)

[M2](https://machinistcharts.com/material/m2-high-speed-steel/) is the standard high-speed steel, with about 6 % tungsten, 5 % molybdenum, 4 % chromium and 2 % vanadium. It keeps its hardness when the cutting edge runs hot, which is why most HSS [drill bits](https://machinistcharts.com/guides/drill-bits-for-metal/) and [taps](https://machinistcharts.com/guides/types-of-taps/) are M2 or a cobalt grade. High-cobalt grades such as M42 are hardened higher than M2 for better hot hardness.

### Mold (P)

[P20](https://machinistcharts.com/material/p20-tool-steel/) is a chromium-molybdenum mold steel normally supplied pre-hardened, so mold cavities are machined to size without a later heat treatment. Stainless martensitic grades such as [420](https://machinistcharts.com/material/420-stainless/) are used as "stainless tool steel" for molds that must resist corrosion.

## Common tool steel grades and typical hardness

The seven grades below cover most tool steel bought by general machine shops and toolrooms. Hardness values are typical working ranges after hardening and tempering, not limits: the tempering temperature sets the final hardness, and each supplier publishes its own heat-treatment data.
[](https://machinistcharts.com/material/o1-tool-steel/)[](https://machinistcharts.com/material/a2-tool-steel/)[](https://machinistcharts.com/material/d2-tool-steel/)[](https://machinistcharts.com/material/h13-tool-steel/)[](https://machinistcharts.com/material/m2-high-speed-steel/)[](https://machinistcharts.com/material/p20-tool-steel/)

| Grade | Class | Quench | Typical working hardness | Typical uses |
|---|---|---|---|---|
| O1 | Oil-hardening cold work | Oil | 57–62 HRC | Gauges, punches, short-run dies, knives, bushings |
| A2 | Air-hardening cold work | Air | 57–62 HRC | Punches, blanking and forming dies, trim dies, gauges |
| D2 | High-carbon high-chromium cold work | Air | 58–62 HRC | Long-run blanking dies, shear blades, slitter knives, wear parts |
| S7 | Shock resisting | Air (oil for heavy sections) | 54–58 HRC | Chisels, punches, rivet sets, shear blades, impact tools |
| H13 | Chromium hot work | Air | 44–52 HRC | Die-casting dies, extrusion dies, forging dies, hot shears |
| M2 | Molybdenum high speed | Oil, salt or vacuum gas | 62–65 HRC | Drills, taps, end mills, reamers, lathe bits |
| P20 | Mold steel | Supplied pre-hardened | about 28–32 HRC as supplied | Plastic injection mold cavities, mold bases, holders |

Higher hardness gives more wear resistance but less toughness. A punch that chips is usually run too hard or is the wrong grade; a punch that wears or mushrooms is too soft or needs a more wear-resistant grade. For how HRC compares with Brinell and Vickers, see the [steel hardness chart](https://machinistcharts.com/guides/steel-hardness-chart/).

Which tool steel is the hardest? Of the common grades, high-speed steels such as M2 reach the highest working hardness, typically 62–65 HRC, and cobalt and powder-metallurgy high-speed steels go higher. "Strongest" depends on the job: D2 resists wear best of the cold-work grades, S7 resists impact best, and H13 holds strength best at heat.

> Hardness ranges and heat-treatment notes on this page are typical. Follow the steel supplier's data sheet for austenitizing temperature, soak time, quench and tempering, and check the mill certificate for the actual grade.

## D2 vs A2 vs O1 tool steel

D2, A2 and O1 are the three most common cold-work tool steels. D2 has the highest wear resistance, O1 is the easiest to machine and heat treat, and A2 sits between them with better toughness than D2 and less distortion than O1.

| Property | O1 | A2 | D2 |
|---|---|---|---|
| Class | Oil-hardening cold work | Air-hardening cold work | High-carbon high-chromium cold work |
| Nominal carbon / chromium, % | about 0.9 C / 0.5 Cr | about 1.0 C / 5 Cr | about 1.5 C / 12 Cr |
| Quench medium | Oil | Air | Air |
| Hardening temperature | Lowest of the three | Medium | Highest of the three |
| Typical working hardness | 57–62 HRC | 57–62 HRC | 58–62 HRC |
| Wear resistance | Medium | High | Very high |
| Toughness | Medium | Medium to high | Low to medium |
| Distortion in hardening | Higher | Low | Very low |
| Machinability, annealed | Best | Good | Poor |
| Typical choice | Small shop tools, gauges, short runs | General dies and punches | Long-run dies, shear and slitter blades |

A2 vs D2: pick D2 when the tool fails by wear, such as blanking abrasive sheet for long runs. Pick A2 when the tool fails by chipping, or when it has thin sections and sharp corners. D2 is also used for knife blades because it holds an edge, at the cost of being harder to sharpen and less tough than simpler steels.

### How to heat treat A2 steel

A2 is hardened by preheating, soaking at the austenitizing temperature, cooling in still air and tempering promptly. In outline: preheat to reduce thermal shock, heat to the supplier's hardening temperature (typically in the range of about 925–980 °C (1700–1800 °F)), soak until the section is through-heated, air cool to near room temperature, then temper at once, usually twice. Wrap the part in stainless foil or use a vacuum or protective-atmosphere furnace to prevent decarburization. The tempering temperature sets the final hardness; use the supplier's tempering curve.

## Tool steel equivalents: AISI, EN, JIS and GB

Tool steel equivalents are the nearest matching grades in European (EN), Japanese (JIS) and Chinese (GB) standards. They are close but not identical, so check composition and hardness requirements before substituting.
[](https://machinistcharts.com/material/d2-tool-steel/)[](https://machinistcharts.com/material/h13-tool-steel/)[](https://machinistcharts.com/material/o1-tool-steel/)[](https://machinistcharts.com/material/a2-tool-steel/)[](https://machinistcharts.com/material/m2-high-speed-steel/)[](https://machinistcharts.com/material/p20-tool-steel/)

| AISI | EN name | EN number | JIS | China GB |
|---|---|---|---|---|
| D2 | X153CrMoV12 | 1.2379 | SKD11 | Cr12Mo1V1 |
| H13 | X40CrMoV5-1 | 1.2344 | SKD61 | 4Cr5MoSiV1 |
| O1 | 100MnCrW4 | 1.2510 | SKS3 | 9CrWMn |
| A2 | X100CrMoV5 | 1.2363 | SKD12 | Cr5Mo1V |
| M2 | HS6-5-2 | 1.3343 | SKH51 | W6Mo5Cr4V2 |
| P20 | 40CrMnMo7 | 1.2311 | — | 3Cr2Mo |

P20 has no direct JIS equivalent; Japanese makers sell their own pre-hardened mold grades. S7 is not in the site's equivalents table. Each grade above links to its [steel grade equivalents](https://machinistcharts.com/material/) page, and other steel families are listed there too.

## Common questions

### What is tool steel?

Tool steel is a carbon or alloy steel made to be hardened and used for cutting, forming, punching and molding. Most grades have about 0.5–1.5 % carbon plus chromium, molybdenum, tungsten or vanadium, and work at about 45–65 HRC. They are specified by AISI class letter and grade number under ASTM A681, A600 and A686.

### What is the difference between A2 and D2 tool steel?

D2 has about 1.5 % carbon and 12 % chromium and gives the highest wear resistance of the common cold-work steels. A2 has about 1.0 % carbon and 5 % chromium and is tougher, so it chips less. Both are air hardening with low distortion. Typical working hardness is 58–62 HRC for D2 and 57–62 HRC for A2.

### What is S7 tool steel used for?

S7 is a shock-resisting tool steel used for tools that are struck or see impact: chisels, punches, rivet sets, shear blades and heavy-duty dies. It has about 0.5 % carbon with chromium and molybdenum, is air hardening in moderate sections, and is typically used at 54–58 HRC, trading some wear resistance for high toughness.

### What is the hardest tool steel?

Of the common grades, high-speed steels reach the highest working hardness: M2 is typically 62–65 HRC, and cobalt grades such as M42 and powder-metallurgy high-speed steels are hardened higher still. Among cold-work steels, D2 is typically 58–62 HRC. Hardness alone does not make a tool last; toughness and wear resistance matter too.

### What does the letter in a tool steel grade mean?

The AISI letter names the class. W, O and A are water, oil and air hardening. D is high-carbon high-chromium cold work. S is shock resisting, H is hot work, M and T are molybdenum and tungsten high-speed steels, P is mold steel and L is low-alloy special purpose. The number then identifies the grade within the class.

### How do you heat treat A2 tool steel?

Preheat, then soak at the supplier's hardening temperature, typically about 925–980 °C (1700–1800 °F), until through-heated. Cool in still air, then temper immediately, usually twice. Protect the surface from decarburization with stainless foil, vacuum or a controlled atmosphere. The tempering temperature sets final hardness, typically 57–62 HRC; follow the supplier's data sheet.

### What is the equivalent of D2 tool steel?

The nearest equivalents of AISI D2 are EN 1.2379 (X153CrMoV12), JIS SKD11 and China GB Cr12Mo1V1. They are nearest matches, not identical grades: composition limits and heat-treatment response differ slightly between makers, so check the standard or mill certificate before substituting.

Source page: https://machinistcharts.com/guides/tool-steel-grades/
Updated: 2026-10-24
Publisher: MachinistCharts (https://machinistcharts.com)
