# Thread classes and fits: 2A, 2B, 3A, 3B, 6g and 6H

Short answer: Thread classes set the tolerance and allowance of a thread. Inch threads use 1A, 2A, 3A for bolts and 1B, 2B, 3B for holes; class 2A/2B is the commercial standard and 2A includes an allowance for plating. Metric threads use tolerance classes such as 6g for bolts and 6H for holes. A standard threaded hole is 6H or 2B.

## Key takeaways

- A = external thread, B = internal thread; class 2A/2B is the default commercial fit.
- Class 2A and 1A bolts have an allowance; 3A bolts and all B holes have none.
- Metric 6g/6H is the ISO 965-1 default fit; the number is the tolerance grade, the letter the position.
- An M8 × 1.25-6H hole has a pitch diameter of 7.188 to 7.348 mm.
- A coating raises pitch diameter by 4 × its thickness, so keep it under a quarter of the allowance.

## What are thread classes?

A thread class sets how much the size of a thread may vary and whether there is a gap (allowance) between bolt and nut. Inch threads use classes 1A, 2A and 3A for external threads and 1B, 2B and 3B for internal threads. Metric threads use tolerance classes such as 6g for bolts and 6H for nuts and tapped holes.

The higher the class number, the tighter the fit. Class 2A/2B and metric 6g/6H are the normal commercial fit and are assumed when a drawing gives no class. Classes control mainly the **pitch diameter**, the diameter where the flanks of bolt and nut meet, defined on the [thread pitch chart](https://machinistcharts.com/guides/thread-pitch-chart/).

### Unified thread classes (ASME B1.1)
************************

| Class | Thread | Allowance | Pitch dia tolerance (vs 2A) | Typical use |
|---|---|---|---|---|
| 1A | External (bolt) | Yes | 150 % | Loose fit; quick assembly with dirty or damaged threads. Rare today. |
| 2A | External (bolt) | Yes | 100 % | Standard commercial bolts and screws; leaves room for plating. |
| 3A | External (bolt) | None | 75 % | Close fit: socket head cap screws, aerospace and precision parts. |
| 1B | Internal (nut, tapped hole) | None | 195 % | Loose fit, paired with 1A. |
| 2B | Internal (nut, tapped hole) | None | 130 % | Standard commercial nuts and tapped holes. |
| 3B | Internal (nut, tapped hole) | None | 97.5 % | Close fit, paired with 3A. |

The tolerance column is the pitch diameter tolerance relative to class 2A, as set in ASME B1.1. Any class A bolt assembles with any class B hole of the same size and series, for example a 2A screw in a 3B hole; the classes only change how loose the fit can be.

## 2A vs 2B threads

2A and 2B are the same class for opposite parts: A is the external thread (bolt, screw, stud) and B is the internal thread (nut, tapped hole). A 1/4-20 UNC-2A bolt is made to fit a 1/4-20 UNC-2B hole. Class 2A includes an allowance; class 2B does not.

The **allowance** is a deliberate gap: the largest 2A bolt is smaller than the basic size, while the smallest 2B hole is exactly basic. So even the fattest 2A bolt fits the tightest 2B hole with clearance, which makes assembly easy and leaves room for plating. On 1/4-20 the allowance is 0.0011 in.

| 1/4-20 UNC class | Major or minor dia (in) | Pitch dia min (in) | Pitch dia max (in) | PD tolerance (in) |
|---|---|---|---|---|
| 2A (external) | Major 0.2408–0.2489 | 0.2127 | 0.2164 | 0.0037 |
| 3A (external) | Major 0.2419–0.2500 | 0.2147 | 0.2175 | 0.0028 |
| 2B (internal) | Minor 0.196–0.207 | 0.2175 | 0.2224 | 0.0049 |
| 3B (internal) | — | 0.2175 | 0.2211 | 0.0036 |

Values from the ASME B1.1 tables for 1/4-20 UNC. The basic pitch diameter is 0.250 − 0.6495 × 0.050 = 0.2175 in. The 2B and 3B minimum pitch diameter equals basic, and 3A maximum equals basic: class 3A has no allowance. The 2B minor diameter range of 0.196 to 0.207 in is why a [#7 drill](https://machinistcharts.com/tap-drill/1-4-20/) (0.201 in) is the standard tap drill.

## 2B vs 3B and 2A vs 3A

Class 3 has a smaller tolerance than class 2, and 3A has no allowance. A 3A/3B fit is closer and more consistent, at higher cost for gauging and tooling. Use class 2 unless a drawing, a fastener standard or a load case requires class 3.

- **3A** pitch diameter tolerance is 75 % of 2A. On 1/4-20 that is 0.0028 in against 0.0037 in.

- **3B** pitch diameter tolerance is 97.5 % of 2A, 0.0036 in on 1/4-20, against 0.0049 in for 2B.

- Socket head cap screws are commonly made to class 3A. Most hex bolts, machine screws and nuts are 2A and 2B.

- A ground thread tap marked with an H-limit (for example H3) cuts a slightly oversize thread within the 2B or 3B band. Ask the tap maker which limit gives 2B or 3B for a given size.

Class 1A/1B is a loose fit with large tolerances for quick assembly in dirty conditions. It is seldom specified today. The [types of taps guide](https://machinistcharts.com/guides/types-of-taps/) covers tap limits and tap styles.

## Metric thread tolerance classes: 6g, 6H, 4h, 6e, 7H

An ISO metric tolerance class is a number and a letter. The number (tolerance grade, 3 to 9) sets the size of the tolerance: 4 is tight, 6 is medium, 8 is coarse. The letter (tolerance position) sets the allowance: lower case for bolts, capital letters for nuts. 6g bolts with 6H nuts are the ISO 965-1 default.
************************

| Position | Applies to | Fundamental deviation | Use |
|---|---|---|---|
| H | Internal | 0 (no allowance) | Standard tapped holes and nuts: 6H |
| G | Internal | +(15 + 11P) µm, approx. | Internal threads that will be plated or coated |
| h | External | 0 (no allowance) | Close-fitting bolts, studs and gauges: 4h, 6h |
| g | External | −(15 + 11P) µm, approx. | Standard commercial bolts: 6g |
| f | External | larger than g | Bolts with medium coatings |
| e | External | −(50 + 11P) µm, approx. | Bolts with thick coatings such as hot-dip galvanizing (6e) |

The deviation formulas are approximate; ISO 965-1 tabulates rounded values for each pitch. For M8 × 1.25 the g deviation is 28 µm and the e deviation is about 64 µm.

### Reading a metric tolerance class

- **6g**: pitch diameter and major diameter both grade 6, position g. The normal class for metric bolts.

- **6H**: pitch diameter and minor diameter grade 6, position H. The normal class for nuts and tapped holes.

- **4h**: tight grade with no allowance, for precision studs and gauges. When two grades are given, as in 4h6h or 5g6g, the first applies to the pitch diameter and the second to the crest diameter.

- **6e**: medium grade with a large allowance, for bolts that will be thickly coated.

- **7H** and **8g**: coarse grades, for hot-rolled threads or long, deep holes where a 6H tap is hard to hold.

ISO 965-1 groups classes into three qualities for normal length of engagement: fine (5H internal, 4h external), medium (6H, 6g) and coarse (7H, 8g). A fit is written internal class first: M8 × 1.25-6H/6g.

## What is the tolerance for threaded holes?

A standard threaded hole is class 6H for metric and class 2B for inch threads. A 6H hole has no allowance: its minimum pitch diameter equals the basic size. For M8 × 1.25-6H the pitch diameter may be 7.188 to 7.348 mm and the minor diameter 6.647 to 6.912 mm.

| Internal thread | Pitch dia min (mm) | Pitch dia max (mm) | Minor dia min (mm) | Minor dia max (mm) | Tap drill (mm) |
|---|---|---|---|---|---|
| M6 × 1-6H | 5.350 | 5.500 | 4.917 | 5.153 | 5 |
| M8 × 1.25-6H | 7.188 | 7.348 | 6.647 | 6.912 | 6.8 |
| M10 × 1.5-6H | 9.026 | 9.206 | 8.376 | 8.676 | 8.5 |
| M12 × 1.75-6H | 10.863 | 11.063 | 10.106 | 10.441 | 10.2 |

Limits calculated from the ISO 68-1 basic profile (d2 = d − 0.6495P, D1 = d − 1.0825P) and the grade 6 tolerances in ISO 965-1. The tap drill must land inside the minor diameter band; see the [tap drill chart](https://machinistcharts.com/tap-drill/), for example [M8](https://machinistcharts.com/tap-drill/m8/) and [M10](https://machinistcharts.com/tap-drill/m10/), and the [thread percentage calculator](https://machinistcharts.com/calculators/thread-percentage/).

### Metric 6g external thread limits
[](https://machinistcharts.com/tap-drill/m6/)[](https://machinistcharts.com/tap-drill/m8/)[](https://machinistcharts.com/tap-drill/m10/)[](https://machinistcharts.com/tap-drill/m12/)

| External thread | Major dia max (mm) | Major dia min (mm) | Pitch dia max (mm) | Pitch dia min (mm) |
|---|---|---|---|---|
| M6 × 1-6g | 5.974 | 5.794 | 5.324 | 5.212 |
| M8 × 1.25-6g | 7.972 | 7.760 | 7.160 | 7.042 |
| M10 × 1.5-6g | 9.968 | 9.732 | 8.994 | 8.862 |
| M12 × 1.75-6g | 11.966 | 11.701 | 10.829 | 10.679 |

A new M8 6g bolt therefore measures 7.760 to 7.972 mm across the crests, never a full 8.00 mm. Inch 2A bolts behave the same way: a 1/4-20 2A measures 0.2408 to 0.2489 in.

> Calipers do not check thread class. Class is accepted with thread gauges: a GO and a NO-GO thread plug gauge for holes and ring gauges for bolts (ASME B1.2 for Unified, ISO 1502 for metric). The GO gauge must screw in fully; the NO-GO gauge must not enter more than a few turns.

## Thread allowance and plating

A coating on a 60° thread raises the pitch diameter by four times the coating thickness, because each flank is coated and the 30° flank angle multiplies the change. So a coating must be no thicker than about one quarter of the allowance, or the plated bolt will not enter a 6H or 2B hole.

| Thread | Allowance es (µm) | Max coating per flank (µm) |
|---|---|---|
| M6 × 1-6g | 26 | 6.5 |
| M8 × 1.25-6g | 28 | 7.0 |
| M10 × 1.5-6g | 32 | 8.0 |
| M12 × 1.75-6g | 34 | 8.5 |
| 1/4-20 UNC-2A | 28 (0.0011 in) | 7.0 (0.00028 in) |

Allowance values: 6g deviations from ISO 965-1, 2A allowance from ASME B1.1. Typical zinc electroplate is thin enough for 6g and 2A. Thick coatings such as hot-dip galvanizing need either an e-position bolt (6e), or a nut tapped oversize after galvanizing. Plating also changes friction, so check torque values on the [bolt torque chart](https://machinistcharts.com/bolt-torque/) and in [the bolt torque formula](https://machinistcharts.com/guides/bolt-torque-formula/).

Unless the drawing says otherwise, 2A limits are sizes before plating, and the plated thread may grow up to basic size. Class 3A has no allowance, so a 3A part that will be plated must be made undersize first, and the drawing should say whether the class applies before or after coating.

## Thread tolerance on drawings

Write the full designation on the drawing: size, pitch, series and class. If the class is omitted, the shop assumes the medium default, 6H/6g for metric and 2A/2B for inch.

- Metric tapped hole: `M8 × 1.25-6H`, with thread depth, for example `M8 × 1.25-6H` with a full-thread depth of 12 mm.

- Metric bolt or stud: `M10 × 1.5-6g`; precision stud: `M10 × 1.5-4h`.

- Inch tapped hole: `1/4-20 UNC-2B`; precision: `1/4-20 UNC-3B`.

- Inch external: `3/8-24 UNF-2A`; rolled thread with rounded root: `3/8-24 UNRF-3A`.

- Left-hand threads add LH: `M12 × 1.5-6H-LH` or `1/2-20 UNF-2B-LH`.

Thread tolerance classes are separate from ISO 286 hole and shaft fits such as H7/g6, which apply to plain bores and shafts. For those, see [bearing fits and clearance](https://machinistcharts.com/guides/bearing-fits-and-clearance/). For thread depth and how much engagement a hole needs, see [thread engagement length](https://machinistcharts.com/guides/thread-engagement-length/).

## Common questions

### What is the tolerance for threaded holes?

A standard threaded hole is toleranced to class 6H for metric threads and class 2B for inch threads. Both have no allowance, so the smallest permitted hole equals the basic size. For M8 × 1.25-6H the pitch diameter is 7.188 to 7.348 mm and the minor diameter 6.647 to 6.912 mm. Holes are checked with GO and NO-GO plug gauges.

### What is the difference between 2A and 2B threads?

2A is the class for external threads such as bolts and screws; 2B is the class for internal threads such as nuts and tapped holes. They are made to fit each other. Class 2A includes an allowance, a small gap below basic size that eases assembly and leaves room for plating; class 2B has none. On 1/4-20 the 2A allowance is 0.0011 in.

### What is the difference between 2B and 3B threads?

Class 3B has a tighter pitch diameter tolerance than 2B: 97.5 % of the 2A tolerance against 130 %. On 1/4-20 UNC that is 0.0036 in for 3B and 0.0049 in for 2B. Both have a minimum pitch diameter equal to basic. Use 2B for commercial work and 3B where a drawing or fastener standard calls for a close fit.

### What does 6g and 6H mean on a thread?

6g and 6H are ISO metric tolerance classes. The 6 is the tolerance grade (medium), and the letter is the tolerance position: lower-case g is a bolt with a small allowance, capital H is a nut or hole with no allowance. 6H/6g is the default metric fit in ISO 965-1, for example M8 × 1.25-6H/6g.

### What is the difference between 6g and 6h?

Both are medium grade 6 tolerances for external threads. 6g has an allowance below basic size, 28 µm on M8 × 1.25, which leaves room for thin plating and eases assembly. 6h has no allowance: the largest bolt equals basic size. 6g is the standard for commercial bolts; h positions are used for precision studs and gauges.

### What thread class are standard bolts?

Standard inch hex bolts, machine screws and nuts are made to class 2A and 2B. Socket head cap screws are commonly class 3A. Standard metric bolts are made to 6g and nuts to 6H. If a drawing gives no class, the shop assumes 2A/2B for inch and 6g/6H for metric threads.

### How much does plating change thread size?

On a 60° thread the pitch diameter grows by four times the coating thickness, because both flanks are coated. A plated bolt must stay inside its allowance, so the coating can be no thicker than about a quarter of it: about 7 µm on M8 6g (28 µm allowance) and about 0.00028 in on 1/4-20 2A (0.0011 in allowance).

Source page: https://machinistcharts.com/guides/thread-classes-and-fits/
Updated: 2026-10-24
Publisher: MachinistCharts (https://machinistcharts.com)
