# NPT tap drill sizes and NPT thread chart

Short answer: Common NPT tap drill sizes without a reamer: 1/16 NPT 1/4 in, 1/8 NPT R (0.339 in), 1/4 NPT 7/16 in, 3/8 NPT 37/64 in, 1/2 NPT 23/32 in, 3/4 NPT 59/64 in, 1 NPT 1-5/32 in, 1-1/4 NPT 1-1/2 in, 1-1/2 NPT 1-47/64 in and 2 NPT 2-7/32 in. NPT threads taper 1:16 and have 27, 18, 14 or 11.5 TPI.

## Key takeaways

- 1/8 NPT tap drill is R (0.339 in); some charts list 11/32 in.
- 1/2 NPT is 14 TPI on a 0.840 in pipe OD; pipe sizes are nominal, not measured.
- NPT tapers 1:16 on diameter, 3/4 in per foot, a half-angle of 1° 47′.
- Hand-tight engagement is about 4 to 5 turns; wrench makeup adds about 3 threads.
- NPT is 60°, BSP is 55°; at 1/2 and 3/4 in both have 14 TPI but they do not seal together.

## NPT tap drill sizes

The common NPT tap drill sizes, drilling without a taper reamer, are: 1/16 NPT 1/4 in, 1/8 NPT R (0.339 in), 1/4 NPT 7/16 in, 3/8 NPT 37/64 in, 1/2 NPT 23/32 in, 3/4 NPT 59/64 in, 1 NPT 1-5/32 in, 1-1/4 NPT 1-1/2 in, 1-1/2 NPT 1-47/64 in and 2 NPT 2-7/32 in. These are shop-standard values; makers' charts differ by a size in places.
****[](https://machinistcharts.com/drill-size/1-4-inch/)[](https://machinistcharts.com/drill-size/letter-d/)****[](https://machinistcharts.com/drill-size/letter-r/)[](https://machinistcharts.com/drill-size/11-32-inch/)****[](https://machinistcharts.com/drill-size/7-16-inch/)****[](https://machinistcharts.com/drill-size/37-64-inch/)[](https://machinistcharts.com/drill-size/9-16-inch/)****[](https://machinistcharts.com/drill-size/23-32-inch/)****[](https://machinistcharts.com/drill-size/59-64-inch/)****************

| NPT size | Tap drill (no reamer) | Decimal (in) | Metric (mm) | Also used |
|---|---|---|---|---|
| 1/16 NPT | 1/4" | 0.2500 | 6.35 | D (0.2460 in) |
| 1/8 NPT | R | 0.3390 | 8.61 | 11/32" (0.3438 in) |
| 1/4 NPT | 7/16" | 0.4375 | 11.11 | — |
| 3/8 NPT | 37/64" | 0.5781 | 14.68 | 9/16" (0.5625 in) |
| 1/2 NPT | 23/32" | 0.7188 | 18.26 | — |
| 3/4 NPT | 59/64" | 0.9219 | 23.42 | — |
| 1 NPT | 1-5/32" | 1.1563 | 29.37 | — |
| 1-1/4 NPT | 1-1/2" | 1.5000 | 38.10 | — |
| 1-1/2 NPT | 1-47/64" | 1.7344 | 44.05 | — |
| 2 NPT | 2-7/32" | 2.2188 | 56.36 | — |

The "also used" column shows the alternative that some tap makers list: a D drill for 1/16 NPT, 11/32 in for 1/8 NPT and 9/16 in for 3/8 NPT. Use the size recommended by the tap maker when it is given. Decimal values for letter and fractional drills are on the [drill size chart](https://machinistcharts.com/drill-size/), for example [letter R](https://machinistcharts.com/drill-size/letter-r/) and [7/16 in](https://machinistcharts.com/drill-size/7-16-inch/).

A tapered pipe tap cuts more material as it goes deeper, so it needs more torque than a straight tap. Drilling, then taper reaming before tapping reduces tap load and gives a fuller thread; reamed holes use a smaller drill. Tap until a male fitting threads in hand-tight by about the L1 length in the table further down, or until an L1 plug gauge sits within one turn of flush.

## NPT thread chart

NPT (National Pipe Taper) is the US tapered pipe thread defined in ASME B1.20.1. It has a 60° thread angle, a taper of 1:16 on diameter, and flattened crests and roots. Sizes from 1/16 to 2 in use 27, 18, 14 or 11.5 threads per inch.
****[](https://machinistcharts.com/drill-size/1-4-inch/)****[](https://machinistcharts.com/drill-size/letter-r/)****[](https://machinistcharts.com/drill-size/7-16-inch/)****[](https://machinistcharts.com/drill-size/37-64-inch/)****[](https://machinistcharts.com/drill-size/23-32-inch/)****[](https://machinistcharts.com/drill-size/59-64-inch/)****************

| Thread | TPI | Pitch (mm) | Pipe OD (in) | Pipe OD (mm) | Tap drill | Drill (in) |
|---|---|---|---|---|---|---|
| 1/16-27 NPT | 27 | 0.941 | 0.3125 | 7.94 | 1/4" | 0.2500 |
| 1/8-27 NPT | 27 | 0.941 | 0.405 | 10.29 | R | 0.3390 |
| 1/4-18 NPT | 18 | 1.411 | 0.540 | 13.72 | 7/16" | 0.4375 |
| 3/8-18 NPT | 18 | 1.411 | 0.675 | 17.15 | 37/64" | 0.5781 |
| 1/2-14 NPT | 14 | 1.814 | 0.840 | 21.34 | 23/32" | 0.7188 |
| 3/4-14 NPT | 14 | 1.814 | 1.050 | 26.67 | 59/64" | 0.9219 |
| 1-11.5 NPT | 11.5 | 2.209 | 1.315 | 33.40 | 1-5/32" | 1.1563 |
| 1-1/4-11.5 NPT | 11.5 | 2.209 | 1.660 | 42.16 | 1-1/2" | 1.5000 |
| 1-1/2-11.5 NPT | 11.5 | 2.209 | 1.900 | 48.26 | 1-47/64" | 1.7344 |
| 2-11.5 NPT | 11.5 | 2.209 | 2.375 | 60.33 | 2-7/32" | 2.2188 |

The pipe OD is the outside diameter of the pipe, and the male thread measures close to it at its large end. A 1/8-27 NPT thread is a 1/8 in nominal pipe size with 27 threads per inch and an OD of 0.405 in (10.29 mm). For a 1/8 NPT tap, use an R drill, 0.339 in.

> Pipe sizes are nominal, not measured. A 1/2 NPT thread does not measure 1/2 in anywhere: the pipe OD is 0.840 in (21.34 mm), and the 1/2 in name comes from the bore of early pipe. Never size a pipe thread by measuring its diameter and rounding to the nearest fraction.

## What does 1/2 NPT mean?

1/2 NPT means a National Pipe Taper thread for 1/2 in nominal pipe size: 14 threads per inch, a pipe OD of 0.840 in, and a taper of 1:16. A full callout is 1/2-14 NPT. The name refers to the pipe size, not to any diameter of the thread.

- **MPT, MNPT or MIP**: male NPT thread (on the outside of a fitting).

- **FPT, FNPT or FIP**: female NPT thread (inside a fitting or tapped hole).

- **1-1/2 NPT**: 1-1/2 in nominal pipe, 11.5 TPI, pipe OD 1.900 in (48.26 mm).

To identify a pipe thread, measure the male OD with calipers and count the threads per inch, then match both to the chart. A male thread measuring about 0.84 in with 14 TPI is 1/2 NPT; about 0.54 in with 18 TPI is 1/4 NPT. For female threads, measure the bore at the opening, which is a little smaller than the pipe OD. The general method is in [how to measure thread pitch](https://machinistcharts.com/guides/how-to-measure-thread-pitch/).

## NPT taper and thread engagement

The NPT taper is 1 in 16 on diameter: the diameter changes by 1/16 in per inch of length, which is 0.75 in per foot. The half-angle of the taper is 1° 47′ to the axis. As the threads screw together they wedge tighter, which is what seals the joint.

ASME B1.20.1 defines the hand-tight engagement L1, how far a male thread enters by hand, and the effective thread length L2, the length of full thread on the pipe. Wrench makeup adds about 3 more threads beyond hand-tight.

| Size | Hand-tight engagement L1 (in) | L1 in turns | Effective thread L2 (in) | L2 (mm) |
|---|---|---|---|---|
| 1/16 NPT | 0.1600 | 4.3 | 0.2611 | 6.6 |
| 1/8 NPT | 0.1615 | 4.4 | 0.2639 | 6.7 |
| 1/4 NPT | 0.2278 | 4.1 | 0.4018 | 10.2 |
| 3/8 NPT | 0.2400 | 4.3 | 0.4078 | 10.4 |
| 1/2 NPT | 0.3200 | 4.5 | 0.5337 | 13.6 |
| 3/4 NPT | 0.3390 | 4.7 | 0.5457 | 13.9 |
| 1 NPT | 0.4000 | 4.6 | 0.6828 | 17.3 |
| 1-1/4 NPT | 0.4200 | 4.8 | 0.7068 | 18.0 |
| 1-1/2 NPT | 0.4200 | 4.8 | 0.7235 | 18.4 |
| 2 NPT | 0.4360 | 5.0 | 0.7565 | 19.2 |

Hand-tight engagement is about 4 to 5 turns for every size. Typical practice is hand-tight plus 1.5 to 3 turns with a wrench, on threads sealed with PTFE tape or pipe dope. Over-tightening a tapered thread can split a female fitting, especially in cast iron, brass or aluminum. In a tapped hole, the full thread depth should be at least L2 so the male fitting can make up fully; see [thread engagement length](https://machinistcharts.com/guides/thread-engagement-length/) for straight threads.

## NPT vs NPTF vs BSPT vs BSPP

NPT and NPTF are both 60° US tapered pipe threads with the same TPI; NPTF (Dryseal) controls crest and root truncation so the threads seal metal to metal without sealant. BSPT and BSPP are British Standard Pipe threads with a 55° Whitworth angle; BSPT is tapered and BSPP (G) is parallel.

| Thread | Standard | Angle | Form | How it seals |
|---|---|---|---|---|
| NPT | ASME B1.20.1 | 60° | Tapered 1:16 | On the thread, with PTFE tape or paste |
| NPTF (Dryseal) | ASME B1.20.3 | 60° | Tapered 1:16 | Metal to metal: crests and roots crush together |
| NPSM | ASME B1.20.1 | 60° | Parallel | Does not seal on the thread; uses a gasket or seat |
| BSPT (R, Rc, Rp) | ISO 7-1 | 55° | Tapered 1:16 (Rp parallel) | On the thread, with sealant |
| BSPP (G) | ISO 228-1 | 55° | Parallel | Bonded washer, O-ring or gasket |

NPT and NPTF parts screw together, but the joint is dry-sealing only when both are NPTF; otherwise use sealant. NPSM is a straight thread that mates loosely with NPT and seals on a seat, as on swivel hose fittings.

### NPT vs BSP
************************************

| Size | NPT TPI | BSP TPI | NPT OD (mm) | BSP major dia (mm) | Difference |
|---|---|---|---|---|---|
| 1/8 | 27 | 28 | 10.29 | 9.728 | different TPI and angle |
| 1/4 | 18 | 19 | 13.72 | 13.157 | different TPI and angle |
| 3/8 | 18 | 19 | 17.15 | 16.662 | different TPI and angle |
| 1/2 | 14 | 14 | 21.34 | 20.955 | same TPI, different angle |
| 3/4 | 14 | 14 | 26.67 | 26.441 | same TPI, different angle |
| 1 | 11.5 | 11 | 33.40 | 33.249 | different TPI and angle |
| 1-1/4 | 11.5 | 11 | 42.16 | — | different TPI and angle |
| 1-1/2 | 11.5 | 11 | 48.26 | — | different TPI and angle |
| 2 | 11.5 | 11 | 60.33 | — | different TPI and angle |

BSP major diameters from ISO 228-1. At 1/2 and 3/4 in, NPT and BSP share 14 TPI, so the threads start and run a turn or two before the 60° and 55° flanks fight. The joint can feel tight and still leak. Do not mix them: use an adapter.

3/8 BSP thread is 19 TPI with a major diameter of 16.662 mm; 3/8 NPT is 18 TPI on a 0.675 in (17.15 mm) pipe. BSPP is marked G, for example G1/4. BSPT is marked R for male taper, Rc for female taper and Rp for female parallel (ISO 7-1). The [metric vs imperial threads guide](https://machinistcharts.com/guides/metric-vs-imperial-threads/) covers Whitworth threads more broadly.

## How to show NPT on a drawing

Call out an NPT thread as size, TPI and series: 1/4-18 NPT. Add NPTF for Dryseal threads. Add the tap drill and depth if the shop needs them, for example "7/16 DRILL × 0.75 DEEP, 1/4-18 NPT". Thread representation on drawings follows ASME Y14.6.

- Specify the tap depth or the fitting gauge condition rather than a diameter: tapered threads are accepted with an L1 plug or ring gauge, not with calipers.

- Show the taper on the drawing or use the NPT note; a tapered thread drawn parallel is still read as tapered when the callout says NPT.

- For a straight pipe thread, write NPSM or G (BSPP) so the shop does not cut a taper.

For straight threads, the tap drill for every metric and inch size is on the [tap drill chart](https://machinistcharts.com/tap-drill/), for example [1/4-20](https://machinistcharts.com/tap-drill/1-4-20/) and [M10](https://machinistcharts.com/tap-drill/m10/), and thread tolerances are explained in [thread classes and fits](https://machinistcharts.com/guides/thread-classes-and-fits/). Tap styles, including pipe taps, are covered in [types of taps](https://machinistcharts.com/guides/types-of-taps/).

## Common questions

### What size drill bit for a 1/8 NPT tap?

Use an R drill (0.339 in, 8.61 mm) for a 1/8-27 NPT tap when drilling without a taper reamer. Some charts list 11/32 in (0.3438 in), which is slightly larger and makes the tap easier to turn. Tap until a male fitting threads in by hand about 4 to 4.5 turns.

### What size drill for a 1/4 NPT tap?

Use a 7/16 in drill (0.4375 in, 11.11 mm) for a 1/4-18 NPT tap without a reamer. 1/4 NPT has 18 threads per inch on a 0.540 in pipe OD. Tap to a depth that lets a male fitting enter hand-tight about 4 turns, then make up with a wrench.

### What size drill for a 3/8 NPT tap?

The common drill for a 3/8-18 NPT tap is 37/64 in (0.5781 in, 14.68 mm); some tap makers list 9/16 in (0.5625 in). 3/8 NPT has 18 threads per inch on a 0.675 in pipe OD. Follow the tap maker's chart when it gives a size.

### What size drill bit for a 1/2 NPT tap?

Use a 23/32 in drill (0.7188 in, 18.26 mm) for a 1/2-14 NPT tap without a reamer. 1/2 NPT has 14 threads per inch and fits pipe with a 0.840 in (21.34 mm) outside diameter. Hand-tight engagement is about 0.320 in, roughly 4.5 turns.

### What does NPT stand for in threads?

NPT stands for National Pipe Taper, the US standard tapered pipe thread in ASME B1.20.1. It has a 60° thread angle and a taper of 1 in 16 on diameter, so the joint seals as the threads wedge together, normally with PTFE tape or pipe dope. NPTF is the Dryseal version that seals without sealant.

### What is MPT thread?

MPT means male pipe thread, normally male NPT; it is also written MNPT or MIP. FPT, FNPT or FIP is the female thread. A 1/2 in MPT fitting has a 1/2-14 NPT external thread that fits a 1/2 in FPT port. The size is the nominal pipe size, not the measured thread diameter.

### How do you measure NPT thread size?

Measure the outside diameter of a male thread with calipers near its large end and count threads per inch, then match to an NPT chart. About 0.40 in with 27 TPI is 1/8 NPT, 0.54 in with 18 TPI is 1/4 NPT, 0.84 in with 14 TPI is 1/2 NPT. Do not round the diameter to a fraction; pipe sizes are nominal.

### What is the difference between NPT and BSP threads?

NPT has a 60° thread angle and BSP a 55° Whitworth angle. Most sizes differ in TPI too: 1/8 NPT has 27 and 1/8 BSP 28; 1/4 and 3/8 NPT have 18 against 19. At 1/2 and 3/4 in both have 14 TPI, but the different angle still leaks. BSPP (G) is parallel and seals on a washer.

Source page: https://machinistcharts.com/guides/npt-tap-drill-sizes/
Updated: 2026-10-24
Publisher: MachinistCharts (https://machinistcharts.com)
