# Metric vs imperial threads and metric to standard bolt conversion

Short answer: Metric and imperial (SAE) threads are not interchangeable. The nearest pairs are M5 and #10, M6 and 1/4 in, M8 and 5/16 in, M10 and 3/8 in, M12 and 1/2 in, and M16 and 5/8 in. Diameters differ by up to 0.7 mm and the pitches never match: M6 is 1.0 mm pitch, 1/4-20 is 1.27 mm. Both use a 60° thread angle; Whitworth uses 55°.

## Key takeaways

- No metric thread has an exact inch equivalent; the closest pairs still differ in pitch.
- M8 × 1.25 and 5/16-18 differ by only 0.06 mm in diameter but bind after about a turn.
- M5 × 0.8 and #10-32 have almost the same pitch; the #10 screw is 0.17 mm smaller and strips easily.
- ISO metric, Unified and NPT threads are 60°; Whitworth and BSP are 55°; Acme is 29°.
- 1/2 BSW has 12 threads per inch, 1/2 UNC has 13.

## Metric to standard bolt conversion chart

No metric bolt has an exact inch (SAE) equivalent. The nearest sizes are M6 and 1/4 in, M8 and 5/16 in, M10 and 3/8 in, M12 and 1/2 in, and M16 and 5/8 in, but the diameters differ by 0.06 to 0.7 mm and the pitches never match, so the threads are not interchangeable.

The table pairs each common metric coarse thread with the inch size of closest major diameter, calculated from ISO 261 and ASME B1.1 basic sizes. A positive difference means the inch bolt is larger.
[](https://machinistcharts.com/tap-drill/m3/)****[](https://machinistcharts.com/tap-drill/m4/)****[](https://machinistcharts.com/tap-drill/m5/)****[](https://machinistcharts.com/tap-drill/m6/)****[](https://machinistcharts.com/tap-drill/m8/)****[](https://machinistcharts.com/tap-drill/m10/)****[](https://machinistcharts.com/tap-drill/m12/)****[](https://machinistcharts.com/tap-drill/m14/)****[](https://machinistcharts.com/tap-drill/m16/)****[](https://machinistcharts.com/tap-drill/m20/)****[](https://machinistcharts.com/tap-drill/m22/)****[](https://machinistcharts.com/tap-drill/m24/)****

| Metric | Dia (mm) | Dia (in) | Nearest inch | Dia (mm) | Dia (in) | Difference (mm) | Metric pitch (mm) | UNC TPI (pitch mm) | UNF TPI (pitch mm) |
|---|---|---|---|---|---|---|---|---|---|
| M3 × 0.5 | 3.00 | 0.1181 | #4 | 2.84 | 0.1120 | -0.16 | 0.5 | 40 (0.635) | 48 (0.529) |
| M4 × 0.7 | 4.00 | 0.1575 | #8 | 4.17 | 0.1640 | +0.17 | 0.7 | 32 (0.794) | 36 (0.706) |
| M5 × 0.8 | 5.00 | 0.1969 | #10 | 4.83 | 0.1900 | -0.17 | 0.8 | 24 (1.058) | 32 (0.794) |
| M6 × 1 | 6.00 | 0.2362 | 1/4 | 6.35 | 0.2500 | +0.35 | 1 | 20 (1.270) | 28 (0.907) |
| M8 × 1.25 | 8.00 | 0.3150 | 5/16 | 7.94 | 0.3125 | -0.06 | 1.25 | 18 (1.411) | 24 (1.058) |
| M10 × 1.5 | 10.00 | 0.3937 | 3/8 | 9.53 | 0.3750 | -0.48 | 1.5 | 16 (1.587) | 24 (1.058) |
| M12 × 1.75 | 12.00 | 0.4724 | 1/2 | 12.70 | 0.5000 | +0.70 | 1.75 | 13 (1.954) | 20 (1.270) |
| M14 × 2 | 14.00 | 0.5512 | 9/16 | 14.29 | 0.5625 | +0.29 | 2 | 12 (2.117) | 18 (1.411) |
| M16 × 2 | 16.00 | 0.6299 | 5/8 | 15.88 | 0.6250 | -0.12 | 2 | 11 (2.309) | 18 (1.411) |
| M20 × 2.5 | 20.00 | 0.7874 | 3/4 | 19.05 | 0.7500 | -0.95 | 2.5 | 10 (2.540) | 16 (1.587) |
| M22 × 2.5 | 22.00 | 0.8661 | 7/8 | 22.23 | 0.8750 | +0.22 | 2.5 | 9 (2.822) | 14 (1.814) |
| M24 × 3 | 24.00 | 0.9449 | 1 | 25.40 | 1.0000 | +1.40 | 3 | 8 (3.175) | 12 (2.117) |

Use the pairing to choose a replacement part, a clearance hole or a wrench, never to swap threads. To convert any dimension, use the [inch to mm chart](https://machinistcharts.com/calculators/inch-to-mm/). Tap drills for both systems are on the [tap drill chart](https://machinistcharts.com/tap-drill/), and full diameter and pitch data is on the [thread pitch chart](https://machinistcharts.com/guides/thread-pitch-chart/).

### Common lookups

- **1/4-20 metric equivalent**: M6 × 1. The [1/4-20](https://machinistcharts.com/tap-drill/1-4-20/) is 0.35 mm larger in diameter and has a 1.270 mm pitch against 1.0 mm.

- **10-32 metric equivalent**: M5 × 0.8. The [10-32](https://machinistcharts.com/tap-drill/10-32/) is 4.83 mm in diameter with a 0.794 mm pitch.

- **Metric equivalent to 1/2 in**: M12 × 1.75. The [1/2-13](https://machinistcharts.com/tap-drill/1-2-13/) is 12.70 mm with a 1.954 mm pitch.

- **Standard equivalent to 8 mm**: 5/16 in. [M8 × 1.25](https://machinistcharts.com/tap-drill/m8/) is 8.00 mm; [5/16-18](https://machinistcharts.com/tap-drill/5-16-18/) is 7.94 mm with a 1.411 mm pitch.

## Are metric and imperial threads interchangeable?

No. Even the closest pairs differ in pitch, and a mismatched bolt either will not start, or starts and then binds after one or two turns. Forcing it strips the weaker thread or leaves a joint that holds a fraction of its rated load.

The dangerous pairs are the ones that almost fit. M5 × 0.8 and #10-32 have pitches about 0.006 mm apart (0.800 against 0.794 mm), so a #10-32 screw can run several turns into an M5 hole and feel tight. The #10 screw is 0.17 mm smaller in diameter, so it engages only on the tips of the threads and strips at low load. M8 × 1.25 and 5/16-18 are within 0.06 mm in diameter but 0.16 mm apart in pitch, so they bind after about a turn.

> Never rely on a mixed metric and inch thread in a structural, pressure or safety-critical joint. If a bolt binds after a turn or two, stop and identify both threads before applying a wrench.

Torque values are also not interchangeable, because stress areas and strength grades differ. Look up the actual size on the [bolt torque chart](https://machinistcharts.com/bolt-torque/), for example [M8](https://machinistcharts.com/bolt-torque/m8/) or [5/16 in](https://machinistcharts.com/bolt-torque/5-16-inch/).

## How to tell metric from imperial threads

Measure the diameter and the pitch. A metric bolt measures just under a whole millimeter size (an M8 measures about 7.76 to 7.97 mm); an inch bolt measures just under an inch fraction (a 5/16 bolt measures about 0.303 to 0.311 in). Then check the pitch with both a metric and an inch pitch gauge.

1. Measure across the crests with calipers and read the result in both mm and inches.

2. Try the metric gauge leaf for the nearest pitch and the inch leaf for the nearest TPI. Hold each against the thread for its full length and look for light between the leaf and the flanks.

3. For close pairs, count crests over a long length. Over 25.4 mm, M8 × 1.25 shows 20.3 pitches and 5/16-18 shows 18.

4. Look at the head: metric bolts carry property class marks such as 8.8 or 10.9; inch bolts carry radial lines for SAE grades. See [bolt grades and markings](https://machinistcharts.com/guides/bolt-grades-and-markings/).

5. Check the wrench size. Metric hex heads take metric wrenches (13 mm for M8); inch heads take fractional sizes (1/2 in for 5/16). The [bolt and wrench size chart](https://machinistcharts.com/guides/bolt-and-wrench-size-chart/) lists both.

The full step-by-step method, with a table of easily confused pairs, is in [how to measure thread pitch](https://machinistcharts.com/guides/how-to-measure-thread-pitch/).

## Thread angle: 60° vs 55° vs 29°

ISO metric and Unified inch threads both have a 60° included angle and nearly the same profile, so they differ only in diameter and pitch. Whitworth and BSP threads have a 55° angle with rounded crests and roots. Acme threads have a 29° angle and metric trapezoidal threads 30°.

| Thread | Standard | Included angle | Typical use |
|---|---|---|---|
| ISO metric (M) | ISO 68-1, ISO 261 | 60° | Metric bolts, screws, tapped holes |
| Unified (UNC, UNF, UNEF) | ASME B1.1 | 60° | Inch bolts, screws, tapped holes |
| NPT, NPTF | ASME B1.20.1, B1.20.3 | 60° | US tapered pipe threads |
| Whitworth (BSW, BSF) | BS 84 | 55° | Older British machinery and vehicles |
| BSP (G, R, Rp, Rc) | ISO 228-1, ISO 7-1 | 55° | Pipe threads outside North America |
| Acme | ASME B1.5 | 29° | Lead screws, vises, valve stems |
| Metric trapezoidal (Tr) | ISO 2904 | 30° | Metric lead screws |

Because the angle is different, a 60° pitch gauge does not seat properly on a 55° thread even at the same TPI. A Whitworth thread also has rounded crests, which look softer than the flat crests of a Unified thread.

## Whitworth threads: BSW and BSF

British Standard Whitworth (BSW) is the coarse series and British Standard Fine (BSF) the fine series, both 55° and defined in BS 84. They are found on older British machinery, motorcycles and cars. Most sizes share their TPI with UNC, but the angle and form differ, so they are not interchangeable.
************************************

| Size (in) | BSW TPI | UNC TPI | BSW vs UNC | BSF TPI | UNF TPI |
|---|---|---|---|---|---|
| 1/4 | 20 | 20 | same TPI, different angle | 26 | 28 |
| 5/16 | 18 | 18 | same TPI, different angle | 22 | 24 |
| 3/8 | 16 | 16 | same TPI, different angle | 20 | 24 |
| 7/16 | 14 | 14 | same TPI, different angle | 18 | 20 |
| 1/2 | 12 | 13 | different TPI | 16 | 20 |
| 5/8 | 11 | 11 | same TPI, different angle | 14 | 18 |
| 3/4 | 10 | 10 | same TPI, different angle | 12 | 16 |
| 7/8 | 9 | 9 | same TPI, different angle | 11 | 14 |
| 1 | 8 | 8 | same TPI, different angle | 10 | 12 |

The 1/2 in size is the clearest difference: 1/2 BSW has 12 TPI and 1/2 UNC has 13. Whitworth wrench sizes are based on the bolt diameter, not the across-flats size, so Whitworth spanners do not match SAE or metric wrenches either.

British Standard Pipe (BSP) uses the Whitworth 55° form. BSPP, marked G (ISO 228-1), is parallel and seals on a washer or O-ring. BSPT, marked R for male and Rc or Rp for female (ISO 7-1), is tapered 1:16 and seals on the thread. BSP pitches are 28 TPI for 1/8, 19 TPI for 1/4 and 3/8, 14 TPI for 1/2 and 3/4, and 11 TPI from 1 to 2 in. The [NPT thread chart](https://machinistcharts.com/guides/npt-tap-drill-sizes/) compares BSP with NPT.

## UNEF threads

UNEF (Unified National Extra Fine) is the third Unified inch series in ASME B1.1, with more threads per inch than UNF. It is used on thin-wall tubing, instrument and optical parts, and short engagements. It shares the 60° Unified form.

Common UNEF sizes: #12-32, 1/4-32, 5/16-32, 3/8-32, 7/16-28, 1/2-28, 9/16-24, 5/8-24, 11/16-24, 3/4-20, 13/16-20, 7/8-20, 15/16-20 and 1-20. 5/8 UNEF is 5/8-24, against [5/8-11](https://machinistcharts.com/tap-drill/5-8-11/) UNC and 5/8-18 UNF. The [UNC vs UNF guide](https://machinistcharts.com/guides/unc-vs-unf-threads/) covers when each series is used.

## Acme thread chart

An Acme thread is a 29° trapezoidal thread for power transmission, used on lathe lead screws, vises, jacks and valve stems. The flat crest and root make it stronger and easier to cut than a square thread. General-purpose Acme threads are in ASME B1.5; basic thread depth is half the pitch.
************************************************

| Acme size (in) | Major dia (mm) | TPI | Pitch (in) | Pitch (mm) | Basic thread depth (in) |
|---|---|---|---|---|---|
| 1/4 | 6.35 | 16 | 0.0625 | 1.587 | 0.0312 |
| 5/16 | 7.94 | 14 | 0.0714 | 1.814 | 0.0357 |
| 3/8 | 9.52 | 12 | 0.0833 | 2.117 | 0.0417 |
| 7/16 | 11.11 | 12 | 0.0833 | 2.117 | 0.0417 |
| 1/2 | 12.70 | 10 | 0.1000 | 2.540 | 0.0500 |
| 5/8 | 15.88 | 8 | 0.1250 | 3.175 | 0.0625 |
| 3/4 | 19.05 | 6 | 0.1667 | 4.233 | 0.0833 |
| 7/8 | 22.22 | 6 | 0.1667 | 4.233 | 0.0833 |
| 1 | 25.40 | 5 | 0.2000 | 5.080 | 0.1000 |
| 1-1/4 | 31.75 | 5 | 0.2000 | 5.080 | 0.1000 |
| 1-1/2 | 38.10 | 4 | 0.2500 | 6.350 | 0.1250 |
| 2 | 50.80 | 4 | 0.2500 | 6.350 | 0.1250 |

Acme threads are written as diameter, TPI, series and class: 1/2-10 ACME-2G is a 1/2 in general-purpose Acme thread with 10 TPI and class 2G fit. Classes 2G, 3G and 4G are general purpose (4G is the tightest); classes 2C to 6C are centralizing threads with a crest fit that keeps the screw on center. A left-hand thread adds LH.

The metric counterpart is the ISO trapezoidal thread, marked Tr, with a 30° angle. It is written diameter × pitch, for example Tr16 × 4. It is not interchangeable with Acme.

| Metric trapezoidal | Major dia (mm) | Pitch (mm) | Nearest Acme by diameter |
|---|---|---|---|
| Tr10 × 2 | 10 | 2 | 3/8-12 (9.53 mm, 2.117 mm pitch) |
| Tr12 × 3 | 12 | 3 | 1/2-10 (12.70 mm, 2.540 mm pitch) |
| Tr16 × 4 | 16 | 4 | 5/8-8 (15.88 mm, 3.175 mm pitch) |
| Tr20 × 4 | 20 | 4 | 3/4-6 (19.05 mm, 4.233 mm pitch) |
| Tr24 × 5 | 24 | 5 | 1-5 (25.40 mm, 5.080 mm pitch) |

## Common questions

### What is the metric equivalent of 1/4-20?

The nearest metric thread to 1/4-20 UNC is M6 × 1. The 1/4 in bolt is 6.35 mm in diameter, 0.35 mm larger than M6, and its pitch is 1.270 mm against 1.0 mm. They are not interchangeable: an M6 nut will not run on a 1/4-20 bolt. Use the M6 only as a replacement for the whole bolt and nut or tapped hole.

### What is the metric equivalent of 10-32?

The nearest metric thread to 10-32 UNF is M5 × 0.8. The pitches are almost the same, 0.794 mm and 0.800 mm, but the #10 screw is 4.83 mm in diameter against 5.0 mm. A 10-32 screw can turn into an M5 hole and feel tight, then strip at low load, so do not mix them.

### What is the standard equivalent to 8 mm?

8 mm is 0.315 in. The nearest inch bolt is 5/16 in, 0.3125 in (7.94 mm), only 0.06 mm smaller than M8. The threads still differ: M8 coarse has a 1.25 mm pitch, 5/16-18 UNC has 1.411 mm and 5/16-24 UNF has 1.058 mm. An 8 mm bolt fits a 5/16 in clearance hole but not a 5/16 in tapped hole.

### Can you use a metric bolt in an SAE thread?

No. Metric and SAE (Unified) threads use the same 60° angle but different diameters and pitches. A mismatched bolt either will not start or binds after a turn or two. Forcing it damages the threads and leaves a joint far weaker than rated. Identify both threads with calipers and a pitch gauge before assembly.

### What is the difference between Whitworth and UNC threads?

Whitworth threads (BSW, BSF) have a 55° thread angle with rounded crests and roots; UNC threads have a 60° angle with flat crests. Many sizes share the same TPI, for example 1/4 in at 20 TPI, but 1/2 BSW has 12 TPI and 1/2 UNC has 13. They are not interchangeable even when the TPI matches.

### What is an Acme thread?

An Acme thread is a 29° trapezoidal power-transmission thread defined in ASME B1.5, used on lead screws, vises and jacks. Basic thread depth is half the pitch. Common general-purpose sizes are 1/2-10, 5/8-8, 3/4-6 and 1-5. The metric equivalent form is the 30° trapezoidal thread, written for example as Tr16 × 4.

### What is a UNEF thread?

UNEF is Unified National Extra Fine, the third inch thread series in ASME B1.1 after UNC and UNF. It has more threads per inch for thin walls and short engagements, for example 1/4-32, 1/2-28, 5/8-24 and 1-20. It uses the same 60° form as UNC and UNF but is not interchangeable with them.

Source page: https://machinistcharts.com/guides/metric-vs-imperial-threads/
Updated: 2026-10-24
Publisher: MachinistCharts (https://machinistcharts.com)
