# Guides

## Bolt torque and tightening

- [Bolt size chart with wrench and socket sizes](https://machinistcharts.com/guides/bolt-and-wrench-size-chart/): This bolt size chart gives the wrench for each bolt: M6 takes 10 mm, M8 13 mm, M10 16 mm (17 mm DIN), M12 18 mm (19 mm DIN); 1/4 in takes 7/16 in, 3/8 in takes 9/16 in and 1/2 in takes 3/4 in. Only a few metric and standard sockets match: 8 mm ≈ 5/16 in and 19 mm ≈ 3/4 in.
- [Bolt grades and head markings](https://machinistcharts.com/guides/bolt-grades-and-markings/): Bolt grades rate bolt strength. Inch bolts use SAE grades: no head marks is grade 2, 3 radial lines is grade 5 (120,000 psi tensile) and 6 lines is grade 8 (150,000 psi). Metric bolts are stamped with a class: 8.8 means 800 MPa nominal tensile and 640 MPa yield; 10.9 and 12.9 are stronger.
- [Bolt preload and clamp load explained](https://machinistcharts.com/guides/bolt-preload-and-clamp-load/): Bolt preload is the tension in a bolt after tightening; it creates the clamp load that holds the joint together. The usual target is 75 % of proof load. An M10 class 8.8 bolt has a proof load of 33.6 kN, so its target preload is 25.2 kN, reached with about 50 N·m dry.
- [Bolt torque formula: T = K × F × d](https://machinistcharts.com/guides/bolt-torque-formula/): The bolt torque formula is T = K × F × d: torque equals the nut factor K times the clamp load F times the nominal diameter d. With K = 0.20 for dry steel and F = 75 % of proof load, an M10 class 8.8 bolt needs 50 N·m (37 ft-lb); oiled at K = 0.15 it needs 38 N·m.
- [Bolt torque sequence and flange tightening patterns](https://machinistcharts.com/guides/bolt-torque-sequence/): A bolt torque sequence tightens bolts in a star (criss-cross) pattern so the joint closes evenly: 1-3-2-4 for 4 bolts, 1-5-3-7-2-6-4-8 for 8 bolts and 1-7-4-10-2-8-5-11-3-9-6-12 for 12 bolts. Tighten in passes at about 30 %, 60 % and 100 % of final torque, then check clockwise at 100 %.
- [How to use a torque wrench correctly](https://machinistcharts.com/guides/how-to-use-a-torque-wrench/): How to use a torque wrench: set the target torque, fit the socket square on the fastener, hold the handle at the grip mark and pull slowly at 90° until it clicks or reads the target, then stop. ISO 6789 allows ±4 % error for most wrenches and recommends calibration every 12 months or 5,000 cycles.
- [Lug nut torque chart and how to torque wheels](https://machinistcharts.com/guides/lug-nut-torque-chart/): Typical lug nut torque is 65 to 80 ft-lb on M12 × 1.25 studs, 70 to 90 ft-lb on M12 × 1.5, 75 to 100 ft-lb on 1/2-20, and 120 to 165 ft-lb on 9/16-18 light-truck studs. Tighten in a star pattern with a torque wrench, retorque after 50 to 100 miles, and always use the vehicle maker's figure.

## Threads and tapping

- [How to measure thread pitch and thread size](https://machinistcharts.com/guides/how-to-measure-thread-pitch/): To measure thread pitch, press the leaves of a thread pitch gauge into the thread until one fits with no light showing and read its marking, in mm for metric or threads per inch for inch threads. Then measure the major diameter with calipers. A bolt reading about 7.9 mm with 1.25 mm pitch is M8 × 1.25; about 0.245 in with 20 TPI is 1/4-20 UNC.
- [Metric vs imperial threads and metric to standard bolt conversion](https://machinistcharts.com/guides/metric-vs-imperial-threads/): Metric and imperial (SAE) threads are not interchangeable. The nearest pairs are M5 and #10, M6 and 1/4 in, M8 and 5/16 in, M10 and 3/8 in, M12 and 1/2 in, and M16 and 5/8 in. Diameters differ by up to 0.7 mm and the pitches never match: M6 is 1.0 mm pitch, 1/4-20 is 1.27 mm. Both use a 60° thread angle; Whitworth uses 55°.
- [NPT tap drill sizes and NPT thread chart](https://machinistcharts.com/guides/npt-tap-drill-sizes/): Common NPT tap drill sizes without a reamer: 1/16 NPT 1/4 in, 1/8 NPT R (0.339 in), 1/4 NPT 7/16 in, 3/8 NPT 37/64 in, 1/2 NPT 23/32 in, 3/4 NPT 59/64 in, 1 NPT 1-5/32 in, 1-1/4 NPT 1-1/2 in, 1-1/2 NPT 1-47/64 in and 2 NPT 2-7/32 in. NPT threads taper 1:16 and have 27, 18, 14 or 11.5 TPI.
- [Thread classes and fits: 2A, 2B, 3A, 3B, 6g and 6H](https://machinistcharts.com/guides/thread-classes-and-fits/): Thread classes set the tolerance and allowance of a thread. Inch threads use 1A, 2A, 3A for bolts and 1B, 2B, 3B for holes; class 2A/2B is the commercial standard and 2A includes an allowance for plating. Metric threads use tolerance classes such as 6g for bolts and 6H for holes. A standard threaded hole is 6H or 2B.
- [Thread engagement length: how much thread you need](https://machinistcharts.com/guides/thread-engagement-length/): The thread engagement rule of thumb is a full-thread length of 1 × the bolt diameter in steel, 1.5 × D in cast iron, brass and bronze, and 2 × D in aluminum, rising to about 2.5 × D in soft aluminum and plastics. An M8 bolt needs about 8 mm of thread in steel and 16 mm in aluminum. Drill and tap deeper than the engagement.
- [Screw size chart and thread pitch chart](https://machinistcharts.com/guides/thread-pitch-chart/): A screw size chart gives each thread's diameter and pitch. Number screws are 0.060 in + 0.013 in × the number, so #10 is 0.190 in. Metric coarse pitches: M3 0.5 mm, M4 0.7, M5 0.8, M6 1.0, M8 1.25, M10 1.5, M12 1.75 mm. Common UNC: 1/4-20, 5/16-18, 3/8-16, 1/2-13. Common UNF: 1/4-28, 5/16-24, 3/8-24, 1/2-20.
- [Types of taps and how to tap a hole](https://machinistcharts.com/guides/types-of-taps/): The main types of taps are taper (7 to 10 chamfered threads), plug (3 to 5) and bottoming (1 to 2). Spiral point taps push chips forward for through holes; spiral flute taps lift chips out of blind holes. Form taps make no chips and need a larger drill: about 5.6 mm for M6 instead of 5 mm.
- [UNC vs UNF threads: coarse vs fine](https://machinistcharts.com/guides/unc-vs-unf-threads/): UNC is the Unified coarse thread series and UNF the fine series, both 60° threads defined in ASME B1.1. On the same diameter UNF has more threads per inch, for example 1/4-20 UNC and 1/4-28 UNF. Fine thread has a 9.5 to 14 % larger tensile stress area, so it is stronger in tension; coarse thread assembles faster and resists stripping better in soft materials.

## Drills and holes

- [Clearance hole chart for metric and inch screws](https://machinistcharts.com/guides/clearance-hole-size-chart/): A clearance hole is slightly larger than the screw so it passes through without threading. Per ISO 273, an M6 screw takes a 6.4 mm close, 6.6 mm normal or 7 mm loose hole; an M4 takes 4.3, 4.5 or 4.8 mm. For inch screws, drill #9 close or #7 free for #10, and letter F close or 17/64 in free for 1/4 in.
- [Drill bits for metal: types, sizes and speeds](https://machinistcharts.com/guides/drill-bits-for-metal/): For most metal, use a high-speed steel (HSS) twist drill with a 135 degree split point; use cobalt (M35 or M42) for stainless and hard steel, and carbide only in rigid machines. Set speed with RPM = SFM × 3.82 / D: a 1/4 in HSS drill runs about 1,380 RPM in mild steel and 610 RPM in stainless.
- [Pilot hole size chart for screws, lag bolts and rivets](https://machinistcharts.com/guides/pilot-hole-size-chart/): A pilot hole should match the screw's root diameter: slightly smaller in softwood, equal in hardwood. For a #8 wood screw drill 7/64 in in hardwood or 3/32 in in softwood. For a 3/8 in lag screw drill 7/32 in in softwood or 9/32 in in oak. A 1/8 in pop rivet needs a #30 drill.

## Bearings

- [2RS vs ZZ: sealed bearings vs shielded bearings](https://machinistcharts.com/guides/2rs-vs-zz-bearings/): 2RS sealed bearings have a rubber contact seal on each side that touches the inner ring, so they keep out water and fine dirt best but add friction. ZZ bearings have a metal shield on each side with a small gap, so they run freer and faster but protect less. Both are the same size: a 6203-2RS and a 6203ZZ are both 17 × 40 × 12 mm.
- [Ball bearing materials: chrome steel, stainless and ceramic bearings](https://machinistcharts.com/guides/ball-bearing-materials/): Most ball bearings use 52100 chrome steel (100Cr6, SUJ2, GCr15) hardened to about 58–65 HRC. Stainless steel bearings use 440C for corrosion resistance at somewhat lower load capacity. Ceramic bearings use silicon nitride balls, about 3.2 g/cm³ against 7.8 for steel: hybrid ceramic bearings have steel rings and ceramic balls; full ceramic bearings are ceramic throughout.
- [Bearing interference fit, press fit tolerances and internal clearance](https://machinistcharts.com/guides/bearing-fits-and-clearance/): A bearing interference fit goes on the ring that rotates relative to the load. For a rotating shaft, the inner ring is pressed on with a k5, k6, m5 or m6 shaft and the outer ring slides into an H7 or J7 housing. On a 6205 (25 mm bore), a k5 shaft gives 2 to 21 µm interference. C3 bearings have more internal clearance than normal to absorb this fit and heat.
- [Static vs dynamic load ratings and bearing life calculation](https://machinistcharts.com/guides/bearing-load-ratings-and-life/): In static vs dynamic load terms, a bearing's dynamic load rating C is the load it can carry for a rated life (L10) of one million revolutions, and its static load rating C0 is the load that causes a tiny permanent dent at standstill. Ball bearing life is L10 = (C/P)³ million revolutions, where P is the equivalent load; roller bearings use the exponent 10/3.
- [How to read bearing numbers](https://machinistcharts.com/guides/how-to-read-bearing-numbers/): How to read bearing numbers: split the code into type, series and bore. In 6205-2RS, 6 means deep groove ball bearing, 2 is the light series, and 05 × 5 gives a 25 mm bore. Bore codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm. Suffixes such as 2RS (rubber seals), ZZ (metal shields) and C3 (extra clearance) do not change the size.
- [Types of bearings and the loads they carry](https://machinistcharts.com/guides/types-of-bearings/): The main types of bearings are ball bearings (deep groove, angular contact, self-aligning, thrust), roller bearings (cylindrical, tapered, spherical, needle), plain bearings or bushings, and linear bearings. Ball bearings suit high speed and light to moderate loads. Roller bearings carry heavier loads because rollers make line contact. Plain bearings slide instead of roll and handle shock at low speed.

## Steel and materials

- [303 vs 304 stainless steel: machinability, corrosion and welding](https://machinistcharts.com/guides/303-vs-304-stainless-steel/): 303 vs 304 stainless comes down to sulfur. 303 contains at least 0.15 % sulfur, which breaks chips and makes it the easiest austenitic stainless to machine. 304 is limited to 0.030 % sulfur, so it has better corrosion resistance, welds well and forms well. Use 303 for unwelded turned parts in mild service; use 304 for welded, formed or wetted parts.
- [304 vs 316 stainless steel: differences, strength and uses](https://machinistcharts.com/guides/304-vs-316-stainless-steel/): The difference between 304 and 316 stainless steel is 2–3 % molybdenum in 316, plus more nickel. Molybdenum raises the typical PREN from about 18–20 for 304 to 24–26 for 316, so 316 resists salt and chlorides far better. Both have the same ASTM A240 annealed minimums: 515 MPa (75 ksi) tensile, 205 MPa (30 ksi) yield. 316 typically costs 20–40 % more.
- [Carbon steel grades: types, numbering and common grades](https://machinistcharts.com/guides/carbon-steel-grades/): Carbon steel grades use the SAE/AISI four-digit system: the first two digits give the family (10xx plain carbon, 11xx free-machining, 41xx chromium-molybdenum) and the last two give carbon in hundredths of a percent, so 1045 has about 0.45 % carbon. Low carbon steel has up to about 0.25–0.30 % carbon, medium 0.30–0.60 % and high 0.60–1.0 % or more.
- [Does stainless steel rust? Why it happens and how to stop it](https://machinistcharts.com/guides/does-stainless-steel-rust/): Yes, stainless steel does rust under some conditions. Its minimum 10.5 % chromium forms a passive oxide film that normally stops rust, but chlorides, crevices, carbon steel contamination, weld heat tint and low-chromium grades can break it. Pitting resistance rises with PREN = %Cr + 3.3 × %Mo + 16 × %N: about 18–20 for 304, 24–26 for 316 and 34–36 for 2205.
- [4140 heat treatment: hardening, tempering and annealing](https://machinistcharts.com/guides/heat-treating-4140-steel/): To heat treat 4140, austenitize at about 845–860 °C (1550–1575 °F), quench in oil and temper at once. Tempering at about 205 °C (400 °F) leaves roughly 51–55 HRC; about 595–650 °C (1100–1200 °F) gives roughly 24–33 HRC. Anneal at about 845 °C (1550 °F) with a slow furnace cool. Values are typical; follow the supplier's data.
- [Stainless steel grades explained: types, families and uses](https://machinistcharts.com/guides/stainless-steel-grades-explained/): Stainless steel grades are iron alloys with at least 10.5 % chromium, which forms a self-healing oxide film. They fall into five families: austenitic (304, 316, 303), ferritic (430), martensitic (410, 420, 440C), duplex (2205) and precipitation hardening (17-4PH). 304, about 18 % Cr and 8 % Ni, is the most common grade; 316 adds 2–3 % molybdenum for chloride resistance.
- [Steel hardness chart: Rockwell, Brinell and Vickers conversion](https://machinistcharts.com/guides/steel-hardness-chart/): A steel hardness chart converts between Rockwell C, Vickers and Brinell. Approximate values for carbon and alloy steel per ASTM E140: 20 HRC is about 238 HV and 226 HB, 30 HRC about 302 HV and 286 HB, 40 HRC about 392 HV and 371 HB, 50 HRC about 513 HV and 481 HB, and 60 HRC about 697 HV. Conversions are approximate.
- [Steel properties chart: physical and mechanical properties](https://machinistcharts.com/guides/steel-properties-chart/): Typical steel properties: carbon steel density 7.85 g/cm³ (0.284 lb/in³), Young's modulus 200–210 GPa (29–30 Msi), thermal expansion 11–13 µm/m·°C, conductivity 45–55 W/m·K and melting range about 1425–1540 °C. 304 stainless is about 7.93 g/cm³, 193 GPa, 17.3 µm/m·°C and 16 W/m·K, and melts at about 1400–1450 °C.
- [Tool steel grades: classes, common grades and hardness](https://machinistcharts.com/guides/tool-steel-grades/): Tool steel grades are named by an AISI letter for the class and a number for the grade. W, O and A mean water, oil and air hardening; D is high-carbon high-chromium; S shock resisting; H hot work; M and T high speed; P mold steel. Typical working hardness: D2 58–62 HRC, A2 and O1 57–62, S7 54–58, H13 44–52, M2 62–65.

Source page: https://machinistcharts.com/guides/
Updated: 2026-10-24
Publisher: MachinistCharts (https://machinistcharts.com)
