# 2RS vs ZZ: sealed bearings vs shielded bearings

Short answer: 2RS sealed bearings have a rubber contact seal on each side that touches the inner ring, so they keep out water and fine dirt best but add friction. ZZ bearings have a metal shield on each side with a small gap, so they run freer and faster but protect less. Both are the same size: a 6203-2RS and a 6203ZZ are both 17 × 40 × 12 mm.

## Key takeaways

- 2RS means rubber contact seals on both sides; ZZ or 2Z means metal shields on both sides.
- Sealed (2RS) bearings protect best against water and fine dirt; shielded (ZZ) bearings run with less friction and at higher speed.
- RZ or 2RZ is a non-contact rubber seal: better protection than a shield, nearly the friction of one.
- Closures never change boundary dimensions: 6203, 6203-2RS and 6203ZZ are all 17 × 40 × 12 mm.
- Sealed and shielded bearings are greased for life by the maker and are not designed to be relubricated.

## Sealed bearings vs shielded bearings

Sealed bearings (2RS) close each side with a rubber lip that touches the inner ring. Shielded bearings (ZZ or 2Z) close each side with a pressed steel disc that clears the inner ring by a small gap. Open bearings have no closure and rely on external seals and lubrication.

All three versions of a bearing number share the same boundary dimensions, so they fit the same shaft and housing. A [6203](https://machinistcharts.com/bearing/6203/), 6203-2RS and 6203ZZ all have a 17 mm bore, 40 mm outside diameter and 12 mm width. The choice is about friction, speed and protection, not size.

### What 2RS means

RS stands for a rubber seal; 2RS means one on each side. The seal is usually nitrile rubber (NBR) bonded to a steel stiffening ring, held in a groove in the outer ring, with a lip that rubs on the inner ring. Some makers add a dust lip or use other elastomers. The contact gives the best barrier against dirt and water but adds drag.

### What ZZ means

Z is a metal shield; ZZ (written 2Z by some makers) means one on each side. The shield is a thin steel stamping fixed in the outer ring. It does not touch the inner ring, so it adds almost no friction. It keeps out larger particles and keeps grease in, but water and fine dust can pass the gap.

### What RZ and 2RZ mean

RZ is a rubber non-contact seal: the rubber lip runs very close to the inner ring without touching it. It seals better than a metal shield with nearly the same low friction. Makers use different letters for this design, for example 2RZ, VV or LLB, so check the catalog key.

## 2RS vs ZZ comparison chart

For most dirty or wet machines, use 2RS. For clean, fast or low-torque machines, use ZZ. The table below shows why.

| Property | Open | ZZ / 2Z (metal shield) | 2RZ (non-contact seal) | 2RS (contact seal) |
|---|---|---|---|---|
| Contact with inner ring | None | No, small gap | No, very small gap | Yes, rubbing lip |
| Friction torque | Lowest | Low | Low | Highest |
| Speed capability | Highest | High, close to open | High, close to open | Lower (lip speed and heat limit it) |
| Fine dust | No protection | Limited | Good | Best |
| Water and splash | No protection | Poor | Fair | Best |
| Grease retention | Depends on housing | Good | Good | Best |
| Temperature limit set by | Lubricant | Grease | Grease and seal rubber | Grease and seal rubber |
| Relubrication | Yes | Not intended | Not intended | Not intended |

Exact speed limits differ between makers and sizes and between seal designs; take them from the catalog. In most catalogs a shielded bearing has the same or nearly the same limiting speed as the open bearing, while a contact-sealed bearing has a lower one.

## Sealed bearing size chart

Sealed bearings by size: this chart lists common sealed ball bearing numbers with their shielded equivalents. Sizes come from ISO 15 boundary dimensions and are the same for the open, 2RS and ZZ versions. The full range is on the [bearing size chart](https://machinistcharts.com/bearing/).
[](https://machinistcharts.com/bearing/608/)[](https://machinistcharts.com/bearing/625/)[](https://machinistcharts.com/bearing/629/)[](https://machinistcharts.com/bearing/6000/)[](https://machinistcharts.com/bearing/6001/)[](https://machinistcharts.com/bearing/6200/)[](https://machinistcharts.com/bearing/6201/)[](https://machinistcharts.com/bearing/6202/)[](https://machinistcharts.com/bearing/6203/)[](https://machinistcharts.com/bearing/6204/)[](https://machinistcharts.com/bearing/6205/)[](https://machinistcharts.com/bearing/6206/)[](https://machinistcharts.com/bearing/6207/)[](https://machinistcharts.com/bearing/6208/)[](https://machinistcharts.com/bearing/6302/)[](https://machinistcharts.com/bearing/6303/)[](https://machinistcharts.com/bearing/6304/)[](https://machinistcharts.com/bearing/6305/)

| Sealed | Shielded | Bore mm | OD mm | Width mm | Inch d × D × B |
|---|---|---|---|---|---|
| 608-2RS | 608ZZ | 8 | 22 | 7 | 0.315 × 0.866 × 0.276 |
| 625-2RS | 625ZZ | 5 | 16 | 5 | 0.197 × 0.630 × 0.197 |
| 629-2RS | 629ZZ | 9 | 26 | 8 | 0.354 × 1.024 × 0.315 |
| 6000-2RS | 6000ZZ | 10 | 26 | 8 | 0.394 × 1.024 × 0.315 |
| 6001-2RS | 6001ZZ | 12 | 28 | 8 | 0.472 × 1.102 × 0.315 |
| 6200-2RS | 6200ZZ | 10 | 30 | 9 | 0.394 × 1.181 × 0.354 |
| 6201-2RS | 6201ZZ | 12 | 32 | 10 | 0.472 × 1.260 × 0.394 |
| 6202-2RS | 6202ZZ | 15 | 35 | 11 | 0.591 × 1.378 × 0.433 |
| 6203-2RS | 6203ZZ | 17 | 40 | 12 | 0.669 × 1.575 × 0.472 |
| 6204-2RS | 6204ZZ | 20 | 47 | 14 | 0.787 × 1.850 × 0.551 |
| 6205-2RS | 6205ZZ | 25 | 52 | 15 | 0.984 × 2.047 × 0.591 |
| 6206-2RS | 6206ZZ | 30 | 62 | 16 | 1.181 × 2.441 × 0.630 |
| 6207-2RS | 6207ZZ | 35 | 72 | 17 | 1.378 × 2.835 × 0.669 |
| 6208-2RS | 6208ZZ | 40 | 80 | 18 | 1.575 × 3.150 × 0.709 |
| 6302-2RS | 6302ZZ | 15 | 42 | 13 | 0.591 × 1.654 × 0.512 |
| 6303-2RS | 6303ZZ | 17 | 47 | 14 | 0.669 × 1.850 × 0.551 |
| 6304-2RS | 6304ZZ | 20 | 52 | 15 | 0.787 × 2.047 × 0.591 |
| 6305-2RS | 6305ZZ | 25 | 62 | 17 | 0.984 × 2.441 × 0.669 |

A 608-2RS (sometimes typed as 6082rs) is the sealed version of the [608](https://machinistcharts.com/bearing/608/), an 8 × 22 × 7 mm bearing. A 6205-2RS is the sealed [6205](https://machinistcharts.com/bearing/6205/), 25 × 52 × 15 mm. How each part of these numbers is decoded is covered in [how to read bearing numbers](https://machinistcharts.com/guides/how-to-read-bearing-numbers/).

## Seal and shield suffixes by maker

Each maker writes the 2RS and ZZ closures with its own letters. The suffixes below are the common double-sided contact seal and double-sided shield codes; makers also offer other seal variants, so always confirm the exact design in the catalog.

| Maker | Double contact seal (2RS type) | Double metal shield (ZZ type) | Example, sealed 6203 | Example, shielded 6203 |
|---|---|---|---|---|
| SKF | 2RSH | 2Z | 6203-2RSH | 6203-2Z |
| FAG (Schaeffler) | 2RSR | 2ZR | 6203-2RSR | 6203-2ZR |
| NSK | DDU | ZZ | 6203DDU | 6203ZZ |
| NTN | LLU | ZZ | 6203LLU | 6203ZZ |
| Koyo (JTEKT) | 2RS | ZZ | 6203-2RS | 6203ZZ |
| Timken | 2RS | see catalog | 6203-2RS | see catalog |

A one-sided closure drops the 2 or the doubled letter: RS, Z, RSH, ZR and so on. A one-sided bearing is fitted with the closure facing the dirt and the open side facing an oil or grease supply.

## When to use 2RS, ZZ or open bearings

Choose the closure from the environment first and the speed second.

- **Use 2RS sealed bearings** for water splash, wash-down, outdoor equipment, wood dust, abrasive grit, agricultural machinery, conveyor idlers, wheels and most hobby machines.

- **Use ZZ shielded bearings** in clean enclosures where low friction or high speed matters: small electric motors, fans, spindles in clean housings, and anything where the drag of a rubbing seal is noticeable.

- **Use 2RZ non-contact seals** when you want better protection than a shield but cannot accept the heat and drag of a contact seal.

- **Use open bearings** where the housing supplies oil (gearboxes, oil-bath housings) or has its own seals and a regreasing path.

Internal clearance is chosen separately: a 6203-2RS C3 is a sealed bearing with greater-than-normal clearance. See [bearing fits and clearance](https://machinistcharts.com/guides/bearing-fits-and-clearance/). For corrosive environments, a seal alone is not enough; the materials in [ball bearing materials](https://machinistcharts.com/guides/ball-bearing-materials/), such as [440C stainless](https://machinistcharts.com/material/440c-stainless/), matter as much as the closure.

### Sealed needle roller bearings

Sealed needle roller bearings exist too, mainly drawn cup types with an integral lip seal on one or both sides. Their designations follow the needle bearing system rather than 2RS and ZZ, so the seal code differs by maker. The [types of bearings](https://machinistcharts.com/guides/types-of-bearings/) guide covers needle bearings in general.

## Can you remove bearing seals and shields?

Rubber seals can often be removed and refitted; metal shields usually cannot. A rubber seal can be lifted out at its outer edge with a thin pick and pressed back into its groove, but the lip is easily cut or bent, and a damaged seal no longer seals. Metal shields are normally crimped or snapped into the outer ring and bend when pried out; they are not designed to go back in.

- Do not pry against the balls or cage; work only at the outer edge of the seal.

- If you clean and regrease, fill only part of the free space; makers typically fill sealed bearings to roughly a quarter to a third of the free space. Overfilling causes heat and churning.

- For a critical machine, fit a new bearing rather than reworking a sealed one.

> A sealed or shielded bearing is greased for life, meaning the life of its grease. If the operating temperature or speed is high enough to shorten grease life, an open bearing with regreasing, or a different closure, may last longer.

## Temperature, speed and friction

A contact seal makes heat. Lip friction rises with shaft speed, which is why a 2RS bearing has a lower speed limit than its ZZ twin. Typical NBR seal compounds are rated to around 100 °C (212 °F) for continuous service; fluoro rubber (FKM) seals are used for higher temperatures. Above the seal's limit the lip hardens and cracks. The grease has its own temperature limit, which often governs a shielded bearing.

The added torque of a contact seal is small in absolute terms but noticeable on light, hand-turned or battery-powered mechanisms. A ZZ bearing spins longer by hand than the same 2RS bearing; that is not a sign of quality, only of lower seal drag.

## Common questions

### What is the difference between 2RS and ZZ bearings?

A 2RS bearing has a rubber contact seal on each side that touches the inner ring. A ZZ bearing has a metal shield on each side with a small gap to the inner ring. 2RS keeps out water and fine dirt better; ZZ has less friction and a higher speed limit. Both versions have identical dimensions.

### Are sealed bearings better than shielded bearings?

Sealed bearings are better for dirty, wet or wash-down conditions because the rubber lip blocks water and fine dust. Shielded bearings are better for clean, high-speed or low-torque machines because the shield does not rub. Neither is better in general; choose from the environment first and speed second.

### Is 6203-2RS the same as 6203ZZ?

They are the same size and interchangeable in a housing: both are 17 mm bore, 40 mm outside diameter and 12 mm wide, the ISO 15 dimensions of a 6203. The 6203-2RS has rubber contact seals and the 6203ZZ has metal shields, so they differ in friction, speed limit and protection, not in fit.

### What does 2RS mean on a bearing?

2RS means two rubber seals: one contact seal on each side of the bearing. Makers use their own letters for the same idea, such as 2RSH, 2RSR, DDU and LLU. A single RS is a seal on one side only. The seal does not change the bore, outside diameter or width.

### Can you regrease a sealed bearing?

Sealed and shielded bearings are greased for life and are not designed to be relubricated. A rubber seal can sometimes be lifted out with a thin pick, the bearing cleaned and regreased to roughly a quarter to a third of the free space, and the seal pressed back. Metal shields usually bend when removed.

### What size is a 608-2RS bearing?

A 608-2RS bearing is 8 mm bore, 22 mm outside diameter and 7 mm wide, with a rubber contact seal on each side. The shielded version is 608ZZ and has the same size. The number reads as type 6 deep groove ball bearing, series 0, 8 mm bore.

### What does RZ mean on a bearing?

RZ means a non-contact rubber seal on one side; 2RZ means one on each side. The rubber lip runs very close to the inner ring without touching it, so it seals better than a metal shield while adding little friction. Makers use other codes for the same design, so check the catalog key.

Source page: https://machinistcharts.com/guides/2rs-vs-zz-bearings/
Updated: 2026-10-24
Publisher: MachinistCharts (https://machinistcharts.com)
